Question about KitchenAid Dishwashers

1 Answer

KitchenAid two drawer dishwasher flashing red lights on both drawers. Would not stop until I turned it off at the breaker box. How do I fix this problem?

Posted by SUSAN MARTENS on

  • SUSAN MARTENS Apr 30, 2012

    What is the number for the service tech?

×

Ad

1 Answer

hkapptech

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 183 Answers

That is an error code. call for service and the service tech can solve

Posted on Apr 30, 2012

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: Fisher & Paykel single drawer dishwasher F1 flashing.

F1 indicates a problem with the Flood sensor. I cleaned all the filters etc. removed the drawer viewed under the drawer, it was dry. There is nothing further I can do, so called the Appliances repair person and booked an appointment for him to determine if an outlet hose is blocked or has a hole in it or whatever. Thanks for all the suggestions Blokes. I'm technically challenged. Happy New Year

Posted on Dec 29, 2008

Ad
Master_Tech

Gary Davd

  • 770 Answers

SOURCE: F & P Double Drawer

Are you sure of the model?? flash a U3 the following is from The FP Manual on the DD-603 Model...........

The last two faults are logged into EE memory.
The other U (user) faults have been removed. The old U2 fault, which was the tub forced open during a cycle, has
been removed completely. Instead if the tub is forced open the product simply pauses as if someone had pressed
the start/pause button. The old U3 fault, which indicated a failure to drain i.e. water left in the tub, will not show up a
fault and the DishDrawer will continue through the cycle

Posted on Jan 22, 2008

Anonymous

  • 1 Answer

SOURCE: dishwasher f1 problem

thanks for the follow up. I ended up calling a service representative in my area to complete the repair. 

Posted on Aug 18, 2008

Anonymous

  • 15 Answers

SOURCE: The top drawer of my Fisher Paykel two drawer dishwasher will not close all the way. Something appears to be stopping it. How do I fix it?

To find out what might be blocking it, you can remove the drawer. There are two tabs one on each side of the drawer near the bottom front. Push those in and pull the drawer out. You can lift the drawer up and push the slides in to get them out of the way. Then you should be able to see into the cabinet and what if anything is stuck behind the drawer

Posted on Apr 30, 2009

Anonymous

  • 2 Answers

SOURCE: Fisher Paykel double drawer dishwasher DS6031

you have an overflow leak problem....shut off circuit breaker or pull fuse....let it dry out for up to 4 days; hopefully overnight; peak under dryer and feel metal drip pan and if wet you might be able to dry with a hair dryer...WHY? the lid did not seal when you put cycle on...the lid lowers and you had something..typically too bid glasses on second shelf that was above the seal lip of the tub...stack correctly after this and no worries...

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My double drawer kitchenaid dishwasher sold red light and beeping during cycle wont turn off and runs even with door open, turned breaker off


If you using upper or lower drawer and this shows up it means the dishwasher has water under the filter board which located on the bottom under the lower drawer. You have to disconnected power,removed the lower drawer, clean the water, replaced filter board, check the dishwasher for leaking.

I’m happy to help further over the phone at https://www.6ya.com/expert/vitaliy_f406165329c75ede

Nov 26, 2017 | KitchenAid Dishwashers

1 Answer

MOD KUDDODPPA O THE CENTER LIGHTS ON BOTH DRAWERS FLASH RED


What drawers are you talking about on a kitchenaid dishwasher?

May 10, 2015 | KitchenAid Dishwashers

1 Answer

I have a two drawer KitchenAid KUDD01DPPA. Upon pushing the start button on either drawer the dishwashers will start. then within a minute they turn red and beep non stop and the dishwashers do not run


Usually this indicates a leak. Open the bottom drawer and look underneath and behind it in the base of the frame and see if there is water sitting in there. If so, dry it out with towels. Once all the water is dried out run the dishwasher again. If the same thing happens and the water returns you will have to find the source of the leak. Sometimes its just a temporary leak from a tall item obstructing the lids from closing and sealing all the way.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/jeffrey_634abadf963e31e5

Feb 27, 2015 | KitchenAid 23 in. KUDD01DPPA Stainless...

1 Answer

My double drawer kitchen aid dishwasher is stuck on rinse mode


I tried this once an it worked. Tech came from Sears an asked where fuse box was. He tripped the breaker for dishwasher. Flipped it back on after 10 seconds. Came to the dishwasher an it was like new again. He said sometimes they need a reset. If that did not work he had to replace the panel. Hope it works for you.

Jan 28, 2015 | KitchenAid Kitchen Aid Architect II 24 In....

1 Answer

My single Fisher & Paykel dishwasher drawer DS603I (Integrated Panel) turns on by itself even after turning off the light switch that controls both units that sit on opposite sides of the sink. The...


Yes ,you may be able to restore function by completely drying the area and PC board located under drawer.Use a hair dryer.
However , you will still have a leak and the problem will return.Usually the leak is drawer lid not closing properly. Suspect lid actuators have failed.Very common.Or some kind of obstruction.The drawer can be removed easily by removing 2 large plastic scews at drawer front.If lid actuators have never been replaced go ahead and do that.It is normal for other drawer to work fine.

Hope this helps you

Aug 16, 2011 | Fisher and Paykel 23 in. DD-603 Built-in...

2 Answers

Kitchenaid 2 drawer dishwasher beeping


its saying its flooded allow a few days and it will go away then fill and drain then fill and drain till all soap is gone

Jun 04, 2010 | KitchenAid KUDD01DSSS Built-in Dishwasher

2 Answers

F 1 Error, blinking, beeping and will not stop even when turned off, so we had to turn the circuit breaker off to stop the noise.


You have a leak.
Either from the top lid seal or bottom lid seal. A s time goes by the water level activates the sensor causing the beep. It won't do anything until you fix the leak.

May 25, 2009 | Fisher and Paykel 23 in. DD-603SS Built-in...

2 Answers

Dishwasher stopped working. Suspect electronics issue.


An expert from another site says it's a faulty control panel and may need new actuators.

Jan 31, 2009 | Dishwashers

2 Answers

F1 light flashing with a picture of a wrench


See http://fixitnow.com/2004/10/appliance-repair-revelation-fisher.htm, or http://www.fixya.com/support/t103415-fisher_paykel_dd_603_dish_drawer

Aug 24, 2007 | Fisher and Paykel 23 in. DD-603SS Built-in...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

1,726 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Mike

Level 3 Expert

4369 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a KitchenAid Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...