Washing Machines Logo

Related Topics:

Question about Kenmore Washing Machines

1 Answer

Kenmore washer stops spinning a few seconds in to the cycle.

The Kenmore washer goes through its normal wash cycle however, when it reaches the rinse cycle it fills with water and agitates. When it reaches the spin cycle it starts into the spin cycle and then it stop a few second into it. I also notice water at the bottom of the washer. When I drain the water from the tub it completes the spin cycle.

Posted by Tigger on

Ad

1 Answer

mike cooper

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 884 Answers

Sounds like the brushes are struggling to get enough power to the motor to spin. Renew motor brushes

Posted on Apr 21, 2012

Ad

5 Related Answers

Terry Schneider

  • 177 Answers

SOURCE: I own a Maytag Performa

sounds like you have a tub seal problem, which took out the bearings, I take it one buzy mom does lots of laundry! Maybe time for a new washer.

Posted on Jul 12, 2008

Ad

Anonymous

  • 2 Answers

SOURCE: kenmore stack washer and dryer

gabehart....sounds like belt is slipping. Replace it. The water pump is on a separate smaller motor so is not affected by the agitator/spin motor.

Posted on Aug 11, 2008

Anonymous

  • 20 Answers

SOURCE: Machine fills and agitates, but won't drain

Please empty your machine and run the machine empty. If the washer goes through the whole cycle without any clothes. Please let me know

Posted on Jan 19, 2009

Anonymous

  • 188 Answers

SOURCE: Kenmore front-load washer stops at rinse cycle

When the washer initially fills for the wash, is it only hot water entering the drum? Try switching the water temperature between hot and cold as it fills. If any of them show little or no water getting through, it sounds too easy but check to make sure water supply taps are on, and that the cold/hot fill hoses aren't reversed. Remove the fill hoses and check any of the screen filters for blockage (in the hoses and in the inlet water valve). When the machine stops and waits to fill but all you hear is a hum, it sounds like there is power going to the valve but water is not able to get through it.
Good luck!

Posted on Mar 03, 2009

Anonymous

  • 10 Answers

SOURCE: Kenmore washer won't stop filling during initial wash cycle

I had the same problem too on one of my washers (not kenmore) it didn't complete cycle because someone turned off the hot water valve. soo i turned on the hot water and it worked fine. keep in mind that mine wasn't a kenmore. hope this helps some...

Posted on Oct 08, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
3answers
0helpful
1answer

A kenmore elite washer won't spin on rinse cycles. Does fine on first wash cycle, fills up for first rinse and then won't spin after that either on first or second rinse.

There are two plastic gears on each end of the motor inside the washer. One of them broke. These gears make the tub spin. They are inexpensive. it is rare that both gears broke but have both of them replaced. Then you don't have to worry about the second gear breaking in a few months.
0helpful
1answer

Kenmore elite washer

hi
unfortunately the programmer is faulty
0helpful
1answer
0helpful
1answer

Kennmore 110.22422. 100 hummms when reaching the spin cycle

your timmer button has given up replace the timmer and it will be fine
1helpful
1answer

Kenmore 70 Series Washer

The lid switch is bad . You can either replace it , or bypass it under the control panel . Try putting a pencil down into the hole on the top where the lid actuator goes into to see if it drains and spins .
0helpful
1answer

Kenmore washer quit working

it may be waiting for a faulty heater to kick in. try it on a cold water wash, no heat and see if it continues the full wash. if it does not then it may have a faulty timer.
0helpful
1answer

Frigidaire top load washer won't rinse

this can be two issues. One could be the control knob. there could be a malfunction here. secondly, you may have a faulty water valve assembly. the relay or solenoid may need to be replaced. i would start with the control knob.
0helpful
1answer

GOES TO SPIN CYCLE THEN STOPS SUDDENLY AND REFILLS WATER IN TUB

Are you sure you don't have a second rinse button that is selected.
Not finding what you are looking for?

Open Questions:

478 views

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

vince

Level 3 Expert

1242 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...