Heating & Cooling Logo

Related Topics:

Question about Heating & Cooling

1 Answer

How do you drain water from a LP1010snr air conditioner?

I plugged in my air conditioner and the code P2 keeps flashing and no air is coming out. I looked up P2 and it means it water detection and I'm suppose to drain out the water. How do I do that? Where is the water?

Posted by asha almas on

Add Your Answer

1 Answer

Sudeep Chatterjee

Sudeep Chatterjee

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    Superstar:

    An expert that got 20 achievements.
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,267 Answers

P2 means the water collection tank is full and needs to be drained. You have to pull the drain plug at the bottom of the unit and drain the water.
Drain the water (small amount actually) in the shower. Note: There is a cap towards the bottom of the unit that you will need to unscrew, then pull out the rubber plug. Fired up the unit after the water drain ... it worked fine.

Posted on Apr 18, 2012

Testimonial: "I did that and let it run for a few minutes and it did work. It's been cool out ever since so when I give a full days worth I'll let you know how it works out. Thanks. :)"

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: looking for bottom drain plug for MPM1-10CR-BB6

Go to home depo and get a 9/16 X 3/8 rubber stopper this works just fine you can call me or E - mail [email protected]

Posted on Aug 15, 2009

Anonymous

  • 2 Answers

SOURCE: Drain Hole for Frigidaire Window Air Conditioner

Leave it alone. DO NOT attempt to create a drain. As long as a window A/C unit is installed properly, (angled slightly down toward the rear) it will drain excess water over the rear lower lip of the unit should it get that high. Many models use some of the collected water/condensation. It gets lifted up by the fan blades to cool the coil.

Posted on Jun 23, 2009

Anonymous

  • 4 Answers

SOURCE: What does the code F1 & F6 mean for the Amana

These codes signify black (F1) or yellow (F6) thermistor problems. May need replaced.

Posted on May 07, 2010

Anonymous

  • 4 Answers

SOURCE: Midea MPK-10CR air conditioner "P2"

If the drip line is raised too high, sometimes the level inside will exceed the trip-point for the pan-level.

Try lowering the drip line so the water runs 'downhill' the whole way. If it still occurs, the sensor in the pan may be stuck.

Posted on Jul 15, 2010

Anonymous

  • 4736 Answers

SOURCE: LG LP0910WNR portable Air Conditioner

The P2 Code you're getting is for a system failure. More than likely a sensor has failed In which case, you should contact LG's Customer Interactive Center at 800-243-0000, as it "may" be covered under Warranty.

Posted on Jul 07, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Super General Split Air Conditioner 2. How to fix Super General Inverter A/C with P2 error code please?
Question edited for clarity.

How do I fix P2 error in AC?
 If the P2 or FL error code is displaying on the air conditioner, remove the drain port cap and tilt the air conditioner to the back so the water runs out of the drain outlet. If no water is draining out when the air conditioner is tilted to the back, the unit will require a repair service.
Dec 11, 2018

More here and videos

https://www.google.com/search?q=super+general+inverter+ac+p2+P2+error+code

..
Read full answer
Dec 13, 2022 • General Heating & Cooling
0helpful
1answer

My portable air conditioner lp1010snr has a pH or pass a P2 flashing in the screen hold the drain plug in back very little water in it I don't know where the reset button is, what else do I do
It's with the water. Drain the bucket, vacuum the tubing. If problem persist it's possibly a bad sensor

If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

Read full answer
Aug 11, 2017 • Heating & Cooling
0helpful
1answer

How do I drain the water from my LG portable air conditioner (LP1010SNR)
Lift up the window securing the AC, and CAREFULLY tilt back the unit. The water lays towards the back of the A/C under the fan.
Read full answer
Apr 17, 2012 • LG Heating & Cooling
1helpful
1answer

Hi I HAVE A DIMPLEX AIR-CON It was already here when I moved into this house but lately after it been for on about 5 mins it stops and it display a code of P2. I dont know how to get hold of a manual...
If your model is a portable AC unit, the P2 indicates that water needs to be drained from the tank.
Turn the unit OFF and unplug it, before draining the water from the lower tank into a shallow sided pan capable of holding at least 1 quart of water. Once it has completely drained, reinsert the drain plug, plug the unit in and turn it ON. The P2 Error Code should have disappeared. If not, press the ON/OFF button twice.

I hope this helped you.
Read full answer
Jul 15, 2011 • Heating & Cooling
0helpful
1answer

We have the portable air condioner model LP1010snr and we have drained the tanks and still have the P2 warning. It will not start working. what can we do?
Turn the Master ON/Off Switch to OFF and unplug the unit for 15 minutes. Then plug the unit back in and turn the Master ON/OFF Switch to ON. Hopefully, during that 15 minute timeout, the electronics reset and reverted back to the original factory settings.

Hope this helped you solve the problem.
Read full answer
Jul 09, 2011 • LG Heating & Cooling
13helpful
3answers

I purchased and LG Model# LP1010SNR on 8-3-10 at Home Depot. It was a floor model and did not come with an owners manual. It has a digital display screen. It is intended to run for several hours at a time...
What happens on this unit is it will suddenly stop followed by a series of chimes. You can reset the unit, but it will end with the same set of chimes. My unit display had a P2 code. As mentioned above, I drained the water (small amount actually) in the shower. Note: There is a cap towards tha bottom of the unit that you will need to unscrew, then pull out the rubber plug. Fired up the unit after the water drain ... it worked fine. If they can make a GI Joe talk ... why can this unit simply say ... "Please Drain". P2 is so intuitive.
Read full answer
Aug 04, 2010 • LG Heating & Cooling
1helpful
1answer

P2 err on mpk-10cr it starts for about 5 seconds then p2 displays and it stops can you gide me to were the problem is
P2 error indicates that the spill reservoir in the base of the unit is full.<br /> <br /> Solution:<br />Move the unit to a location that is suitable for draining water from the unit. Remove the plug in the lower center of the back of the unit and allow the water to completely drain <br />(Remember to replace plug.)
Read full answer
May 25, 2010 • Danby DPAC8020 Air Conditioner
1helpful
2answers

My unit displays P2 mode flashes red wont turn.....
P2 error indicates that the spill reservoir in the base of the unit is full.
Solution:
Move the unit to a location that is suitable for draining water from the unit. Remove the plug in the lower center of the back of the unit and allow the water to completely drain (Remember to replace plug.)
Remember...this is not the water tank on the side. This is the water than can collect in the bottom of the unit. Take it outside and drain it
Read full answer
Aug 20, 2009 • Heating & Cooling
13helpful
2answers

Everstar Model MPK-10CR, What does flashing P2 mean?
p2 means the bottom pan is full, you need to drain the bottom, small valve on the back bottom in the middle
Read full answer
Aug 13, 2009 • Danby DPAC8020 Air Conditioner
29helpful
8answers

Everstar MPM1-10CR-BB6
The directions have the steps to take when a "P1" error is flashing.

1) Remove the plug (the upper black plug not the lower) and attach the included drain hose.
2) Put a bucket under the hose.
3) Press the TURBO button for MORE THAN THREE SECONDS. The WATER INDICATOR will begin flashing telling the user that the FORCED WATER DRAINAGE feature is activated. You will even hear a little whirring noise.
4) Wait until the WATER INDICATOR stops flashing and no more water is flowing out of the drainage tube.
5) After the water is finished flowing, make sure that you FASTEN the DRAIN PLUG. Of course, failure to do this will flood the area.
6) The unit should now work.

You can also move the unit somewhere that you can remove the plug and let the water flow freely (you do not need to have it plugged in for this method) and once the water is finished, replace the plug and fire it up. It should then work correctly. It's also mentioned that the water should be drained quite often to prevent corrosion. I do it every few months and of course when winter approaches.

I like this air conditioner and have had really nice luck with it. A little loud but who cares. That's why there are SUBTITLES on the television.

Hope this helped.

RoC
Read full answer
Jun 17, 2008 • Danby DPAC8020 Air Conditioner
Not finding what you are looking for?

View Most Popular

Heating & Cooling

Related Question

Super General Split Air Conditioner 2. How to fix Super General Inverter A/C with P2 error code please?

  • General Heating & Cooling

Open Questions:

0answers

sta-rite thermistor or air in the supply line? unit shuts off and on
Read full answer
Be the first to answer Dec 29, 2022 • Heating & Cooling
0answers

I have a Cdn Fireplace Mfg model DV34 (RN) which I am advised requires a new mercury switch. Where can I buy one? The serial number on my INSTAFLAME fireplace is 08N 8445
Read full answer
Be the first to answer Dec 28, 2022 • Heating & Cooling
0answers

my light is blinking 4 times it will kick off and on then it stops kicking on and i cant find my model number online so i cant do the repairs
Read full answer
Be the first to answer Dec 24, 2022 • Coleman Mobile Modular Home Electric...
0answers

Manual for Marco fireplace model 792792
Read full answer
Be the first to answer Oct 16, 2022 • Heating & Cooling

1,503 views

Ask a Question

Usually answered in minutes!

Popular Questions

Patio heater won't stay lit

Williams 2509612 Ceramic Mid-Size...

New heating pad not working

Sunbeam 805810 HeatSense Heating Pad...

Compressor makes noise and goes on and off constantly

Heating & Cooling

My Sunbeam electric blanket controls

Heating & Cooling

Heater keeps shutting off !!

Lasko 5132 Ceramic Compact Heater

Top Heating & Cooling Experts

Paul Carew

Level 3 Expert

3758 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

john h

Level 3 Expert

28844 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
L0702035 (1).pdf. user-manual-KY-20U...

Soleus KY-20U Air...

PDF Manual
Rads51j.pdf. user-manual-RADS-51 Air...

Comfort-Aire RADS-51...

PDF Manual
5536 Lasco CeramicTowerHeater.pdf....

Lasko 5536 Ceramic...

Loading...