Televison & Video Logo

Related Topics:

Question about Bush 2871NTX 28" TV

1 Answer

Bush 2871ntx need to reset values/check pic

The set is a bush model 2871ntx (in uk)it had a burnt out e/w/inductor and s/c lopt transistor after replacement a very bright raster appears with severe pincushion followed by shutdown after app 10 seconds is it possible that stored values in pic have been corrupted ? and how canthey be reset? (all psu voltages seem ok)any help would be much appreciated. thanks-regards vic h

Posted by victor holbrook on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 372 Answers

Hi.

From memory check resistor R603 its either 2R2 ohm or 2R7ohm, Check the large polyester HV caps for bulging & dry joints.

Chris.

Posted on Nov 25, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer
3helpful
3answers

After changing c5707/c5706 transistors its burnt after 10 minute? i have changed its 3 times, pls advise me about actual problem

On E152fpb dell only replace all driver transistor the c5706 or c5707 this 2 types of transistor is not desame one is PNP & NPN so you must be careful of replacing component maybe it will help you
3helpful
1answer

Logic colour TV stuck in standby mode.

hi! try floating the b+ pin of the lopt and check if you have a normal b+ if it has. the lopt is the culprit.
0helpful
3answers

Inductor L2 Broken of NDS Lite

0 Ohms. You can just bridge it with solder.
0helpful
1answer

Bush TV Dead MODEL: 5693D

switch mode power supply? it has a in or primary side and out the secondary side of a switch mode transformer.

check the driver IC that runs Q102 it makes a oscillation that Q102 amplifies. now the secondary if has a short will blow the Q102 look for shorted rectifiers in the secondary and fuse resistors that are open, even go far downstream and check the HOT for short.
0helpful
2answers

Need a manual

can you supply me with a user manual for a bush 28inc tv receiver model 2863 ntx/a
email [email protected]
kind regard w ward
1helpful
1answer

Tv does not turn on.

There is probably a short or a near short loading the power supply circuit, a leaky capacitor, shorting diode, transistor,IC,LOPT etc. Have the set checked by a technician near you.

It is still worth repairing!

[email protected]
2helpful
1answer

Zoom in and zoom out

Hi.

Try looking in the menu under PICTURE. see if there is picture size adjustment for picture size eg 16 x 9 4 x 3 normal wide.
0helpful
1answer

Bush 2878N TXSIL : Instruction Manual and Remote ?

You may lose some channels when you retune the TV as the channels have been rearranged. To locate them look at the EPG although you may still find that some channels are no longer available on FREEVIEW. See the following link for additional information

http://www.freeview.co.uk/_retuneinfo/

If the above process does not work then check the link above for additional information and also visit the accompanying site links below to find more information for your model of TV / FREEVIEW box.

For troubleshooting the retune procedure visit http://tvretune.co.uk/troubleshooting/

For specific model information visit http://tvretune.co.uk/productmanuals/
Not finding what you are looking for?

84 views

Ask a Question

Usually answered in minutes!

Top Bush Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76849 Answers

Joseph Hoffmann

Level 3 Expert

1756 Answers

Tom Chichester

Level 3 Expert

62329 Answers

Are you a Bush Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...