Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher Logo

Related Topics:

Question about Whirlpool GU1100XTLB / GU1100XTLQ / GU1100XTLT Built-in Dishwasher

1 Answer

Cycles won't run

When the dishwasher is started the water fills up and as soon as the cycle starts, it immediately stops and then drains the dishwasher, This happens in all the cycles with the exception of the "Quick Wash" cycles which appears to work just fine. We had a repair man out who diagnosed the problem to be the electrical control board. I replaced this part which was very expensive and it made no change at all. The machine still fills and empties without washing. Is there anything else that would control this? The frustrating thing is that one cycle will work but none of the others do.

Posted by Dean Crapo on

  • Dean Crapo Nov 21, 2006

    Thanks for the info catriver.

    I was able to find the instructions and put he unit into the test mode which it ran through just fine. Is their something that I am to be looking for during this cycle as it appeared to run through it without any problems?

×

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 878 Answers

Dc, sounds more like a shorted interface, a shorted keypad will act like this. There should be a tech sheet behind the toe panel on the bottom. It should have instructions on how to test the keypad and put the unit into the test cycle. Catriver..post back.

Posted on Nov 17, 2006

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do I fix my Danby Dishwasher? It fills with water then immediately drains.

Most likely the flood switch is triggered. This causes the pump to operate as soon as you start it. Check if the float at the base comes up when you press it by hand. If not the float spring might be stuck and pressing the flood switch underneath.
0helpful
1answer
0helpful
1answer

Water drained out of tube, but dishwasher stops and indicators tell me "drain is plugged."

The drain hose on a dishwasher must be long enough to go up above the water level of the dishwasher and then back down to connect to the sink drain. This is to keep gravity from draining the tank. However, you probably replaced the drain hose the same way it was originally.
Try checking the float and float switch for smooth operation. Maybe the float has debris holding it up from dropping to the true water level.
0helpful
1answer

My top dishwasher drawer won't finish through the cycle. It runs fine on rinse only but not any of the wash cycles. It stops mid cycles, beeps like it has been paused, then tries to start again

Try to feel the temperature of water inside the dishwasher. If it is normal room temperature for the hot wash cycles then it is likely the heater is faulty.
It is not easy to replace unless you have good experience with repairing dishwashers.
0helpful
1answer

Brand new SGS57A02GB just fitted. Run initial cleaning wash to get rid of factory water. Drain starts then stops, starts filling, goes through 2 filling cycles then the drain pump starts. The drain pump...

Hi,

This problem is mostly caused by the drain pump or a restricted drain line. Try taking the end of the drain hose off under the sink and re-checking the drain-out condition. If the unit is still not draining, I recommend replacing the drain pump.

Other possibilities could be that the sump is blocked, or the control or harness may need to be replaced.

Hope this helps.

Shane
1helpful
2answers

Maytag DWU6602AAE. My Maytag dishwasher (14 years

SOUNDS LIKE A TIMER PROBLEM. YOU MAY WANT TO PRICE A REPLACEMENT TIMER. AND PRICE OUT NEW DISHWASHERS. GOOD LUCK!

If you need further help, I’m available over the phone at https://www.6ya.com/expert/dude_653d05454b389bba

Feb 25, 2010 • Dishwashers
0helpful
1answer
3helpful
2answers

Open the dishwaser while still filling now keeps going to error

After reading a few of the other Haier models troubles, I pulled the unit out and tip it at 45 degrees backwards for around minute. Water pored from the back of the unit, once cleaned water up reinstalled unit and all seems to be back in working order.
0helpful
1answer

Whirlpool dishwasher will not fill with water

turn the valves to the left if there the screw in type or parraell if the quick open type the first thing a dishwasher does when you start it is drain for a few minutes then stops then fills with hot water run the water as hot at the sink as you can before starting the washer there is a float in the tub that can shut the water valve off if its not seated on the safety switch after the drain at the start of cycles stops then you should hear the water valve open and start the fill let me know and we will go from there
0helpful
1answer

18 in dishwasher drains water during cycles

find out how the dishwasher is set up to drain. Pour water into dishwasher 4 or 5 gallons, see if water disappears. if so, your drain is ran wrong
Not finding what you are looking for?

196 views

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Oloyede Monsuru

Level 3 Expert

1468 Answers

Mike

Level 3 Expert

4382 Answers

Ekse

Level 3 Expert

13435 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...