Question about Faber Pro Magnum 605989 Kitchen Hood

Open Question

Grease dripping out of control panel

We have the Faber Pro Magnum and we love it's blower power. It is a little loud at full blast but the exhaust is great. However we have been using it for 5 years and though we have cleaned the filters fairly regularly the grease seems to have built up in the channels on the control panel is oozing grease as well as the area nearer the back of the range. It looks like it is hard to reach that area. Any wisdom on how to clean this and stop the build up? Thanks David

Posted by David Epstein on

  • kenneth a Aug 23, 2008

    I also have the same problem with grease dripping down from my FABER PRO MAG exaust and it was installed about 5 years ago. I would appreciate any tips on how to clean the interior of this unit

    P.S. the unit works great



1 Related Answer



  • 10515 Answers

SOURCE: Before I call for a


As the fan is not working but the light does work, it is either a defective fan switch or burned out fan motor. You can replace either one without removing the vent hood from the wall, but you need to use an ohm meter to decide which component is defective.

The fan switch should have 0 ohms of resistance when switched on. If it doesn't, replace the switch. If it does, you need to replace the fan motor.

Note - This is only for informational purpose.This is mere speculation what could be the cause on the basis of the symptoms you mentioned.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Sep 20, 2010


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Magnum pellet stove won't light. Can hear the blower going bit it's like its getting no air

HI this is Duane from Techcenter1. We are the technical experts for MagnuM and Country Flame products. Depending on what model of MagnuM that you have, the air flow would be different. On all models it is important to check for plugging somewhere in the heat exchanger system, worn out exhaust blower or impeller in the exhaust blower, loose doors or failing control board. If you like you can email [email protected] with pictures of your unit and we can easily identify and start to help you out.

Oct 20, 2014 | Pool & Spa

1 Answer

Carol LeBlanc

please follow this link to find a servicer:

Nov 25, 2013 | Faber Inca HC SS Stainless Standard Insert...

1 Answer

The air condition air flow has problems

check blower fan for loose ground and power supply

Jun 23, 2012 | Air Conditioning and Heat for Mercury...

1 Answer

1999 mercury mystique fan blower

So, it works on all settings except for full power?Sounds like the switch in the climate control unit itself.

Jan 03, 2012 | 1999 Mercury Mystique

1 Answer

We just moved into an older home, the 220 dryer outlet is set up for prongs. I went to a hardware store and bought a Magnum 4-wire cord that matches the outlet. My dryer has a 3 wire cord. I removed the...

The red and black are the "hot" wires... white is the neutral and the green gets hooked to the frame of the dryer...

Here is a tip that gives more detail...
Dryer Cord and Wiring Dryer 3 Wire or 4 Wire


Aug 28, 2010 | Faber Pro Magnum 605989 Kitchen Hood

2 Answers

2005 dodge 3500 ram / noise from a/c on passenger side. Very loud when fan is on full blast - not much ac blowing out.

Sounds like you either have something stuck in the blower motor (leaves, pine needles, etc?) or the blower motor bearings are worn out.

Apr 26, 2010 | 2005 Dodge Ram 3500

1 Answer

2000 Volvo V70 climate control problem - blower remains in high, regardless of AUT 0-High setting. Vent selection and temperature controls work. Any idea?

Most common cause of this problem is a bad climate control power stage. The power stage control the speed of the blower fan on different settings, if it goes bad it defaults to full blast. There is a small chance the climate contro lunit itself is bad but more than 90% of the time, it is the power stage. It is located near the blower fan under the dash in the passenger footwell area. It makes it much easier to remove the glove box and knee bolster as well as the cover panel. It is rectangular in shape about 1.5" x 3" and black.

Nov 01, 2009 | 1999 Volvo V70

1 Answer

The fan hardly blows out, even when on full blast

check were the blower is at that panel were the air runs thru it gets full of dirt you might want to clean it out that will help.

Jun 11, 2009 | 1994 Ford Escort

1 Answer

Automatic temperature control system

I am not sure I understand your question. When the control head is turned off, the system goes to defrost mode (failsafe by design) and the blower should be off. If the blower is at high speed when the control is in off, you have a faulty blower speed control module (power mosfet is probably shorted).

Dec 31, 2008 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

GE Profile Refrigerator - Small Leak & Loud Noise

Does water come out of the water dispenser?

I is more likely that the tube that drains the water down from the self defrost mechanism is clogged. Look in the very back of the reefer cabinet, you will see a trough back there, if it is full of ice and water the drain tube is clogged up. If so, a little blast of air from a can of air (like the ones you use to blow off computer key boards will blow it out. Then the water can drain down to the evaporator pan and you will no longer get water on the floor.

Nov 06, 2008 | GE Profile PSW26P Stainless Steel Side by...

Not finding what you are looking for?
Faber Pro Magnum 605989 Kitchen Hood Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Faber Kitchen Ranges Experts


Level 3 Expert

85239 Answers

Paul Carew

Level 3 Expert

3534 Answers

ADMIN Canada
ADMIN Canada

Level 3 Expert

36841 Answers

Are you a Faber Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides