Need I/R code that works for Toshiba D-VR660

Hi joe holmes, my name is Mike Houston of DISH Network and withconnecting the VCR to the DISH receiver you will want to make sure the VCR ison the channel for the DISH receiver. I will send a link that will help withthese steps; http://www.dishnetwork.com/supportsection/receiver-to-tv2

I bought a set-top converter box from Dish Network, which will operate with the DMR-EH75V through the remote control cable that was provided with the recorder. It tunes in all the available digital channels and uses the RCA A/V cables to connect to IN1 on the back of the recorder. TVGOS is now provided through channel 2.1 (CBS) in our area and it also provides the time signal that keeps the recorder's clock updated. NOTE: ONLY the Dish Network boxes work with these functions. I've had occasional issues with the box after some period - a few weeks - it needs to be rebooted or reset to manual and then back to automatic (which causes it to reboot anyway.) Model no is DTV PAL PLUS.

If the problem is the vcr section you load a tape and it shuts down, it probably is the idler assembly that is not transporting tape correctly. I recommend a vcr/tv tech to check the unit with an estimate.

The output of the Dish Network box should be hooked to the input of the VCR.
The output of the VCR should be hooked to the input of the TV.
The VCR should be on channel 3 to record. Select channel to be recorded on the Dish Network box.

It sounds like you have Dish Network box output hooked to TV input.
& VCR output hooked to an aux. input on the TV.

Just put the tape and a blank cd in and just press the Copy from the case.

DISH Changed there policies.

The Sony RM-YD029 Remote control will work with the Dish Network VIP722 DVR HD Satellite Receiver, but the Dish Network VIP722's Primary remote address must be set to 1.

The procedure below will allow Sony RM-YD029 remote control to operate Dish VIP722.

Using the Dish Network Remote Control -
1. Press menu 2 times to get to system info page
2. In the system info page the primary remote address is in a white box (bubble) followed by a Green TV (1)symbol that says IR and indicates you the channel your remote control one is configured. The Sony RM-YD029 will work when this primary remote address number (in the white box) is set to 1.

If the Primary Remote Address of your VIP722 Remote control 1 is not set to channel 1, here is how to change it:

1. While displaying the system info page, press and hold the SAT button on your dish network remote until all other modes are flashing, about 3 seconds.
2. then press the '1' button on the numeric pad of your dish remote
3. then press the '#' button on the numeric pad of the dish remote
4. then press the 'record' button (red dot button - stores setting)
5. At this point you should see a number 1 in front of the primary remote address on the dish system info page

Ensure you enter the corresponding IR code into your Sony remote control per the instructions in the manual or Sony's web site. My 722 works with Sony IR code - 01775.

Here's the link to the owners manual.
http://www.tacp.toshiba.com/tacpassets-images/models/d-vr660/docs/d-vr660_om_e.pdf

I had a device (I forget the brand name) but I could not find the code. There is a way to check all the codes one by one and it didn't take me very long. I can't remember exactly how to do it though. 
it was something like you enter this one specific code that allows you to keep trying to turn the device off and each time you try it will go to the next  code. When the device turns off you know you have the right code and you press a button to lock it in.
I did it through bright house but I would think that dish has something similar. I found it on the bright house website from the problem solving menu.  Try looking for something similar at the dish net website.
Hope that helped. Wish I could be more specific.

Hi first of all are you using scart leads to plug into each device here is how it should be set up ok
1. Scart lead from dish network into vcr
2. then other scart from vcr into tv
3. Now ti recieve the signal from the dish network you need to have the telly on the right av channel so that its picking up the signal from the vcr.
you can test this by changing the channel on the vcr controll or direct via buttons on vcr.
If the channels change then your on the right av channel.
Now when your on right channel on telly you need to now make sure dish network is on and on a channel or press the tv guide button just so you know what your looking for when the picture comes through.
You need to press av on the vcr controll this will then pick up the signal from the dish network via the scart lead as av is the channel for scart lead.
say if you was recording from dish net to vcr you would put the vcr on av to pick up the signal so press av on vcr controll this should then allow you to watch the dish network with no problems.
Let me know if you still cant and ill assist you further if it dont work tell me what you have done so i know how much you have done ok