Question about GE Profile Spectra JGBP90 Gas Kitchen Range

1 Answer

F2 code At certain times it seems like when the oven is not clean, that the F2 comes on. I do not have an owner's manual and do not know what this means. We can not afford to buy a new oven and this is not that old. So please help if possible, Thanks Susan

Posted by Susan Glassberg on

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 878 Answers

Susan, Im assuming that this code is coming up when you are using bake. An F2 code during bake means that the control senses an oven temperature above 650 degrees. Now I doubt if this is the case so you need to look at the temperature sensor for too high of resistence in the circuit. Another possibility is welded relay contacts in the Electronic control itself. With out being there and doing the checks, I would lean toward a new temp sensor. Easy job, part number is WB20K04, look it up on the net to see what it looks like and pricing. Catriver...post back.

Posted on Nov 03, 2006

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Sf367lxss 2 turns off during preheat

F2 E0 is certainly a the error for a stuck key on the pad. Did you buy a new? If so you need to return it and have it replaced. Here is the part to order.

All parts come with a 365 day, any part, any reason return policy.

tip

Whirlpool oven, stove and range fault codes (ERC and EOC display errors).

Here a list of Whirpool oven fault codes. The codes had been collected from different service manuals. This was a memo that I wrote for my own use. I think this can be useful to owners and technicians.

WHIRLPOOL - most models
Range/Stove and Oven Fault Codes, Common error codes.

F1 - Analog control board Failure
Disconnect for one minute - if error comes back, replace control board
F1 - Shorted control keypad
Replace keypad
F3 - Oven temperature sensor open
Replace oven temperature probe
F2 - Oven temperature sensor shorted
Replace oven temperature probe
F3 - Oven too hot
Replace oven temperature probe
F3 - Clean temperature too hot
Replace oven probe
F5 - Door latch switch fault
Test and replace the door switch.


Whirlpool with 4 Digit Failure Code:

F1 - E1 - Electronic control (flip flop)
Replace control board
F2 - E0 - Shorted control keypad
Replace keypad
F3 - E0 - Oven temperature probe open
Replace temperature probe
F3 - E1 - Oven temperature probe shorted
Replace temperature probe
F3 - E2 - Oven temp too high
Replace temperature probe
F3 - E3 - Clean temp too hot
Replace temp. probe
F5 - E0 - Check door latch
F5 - E1 - Check door latch
Replace switch if defective

WHIRLPOOL Polara models 5 digit codes:

F1 F0 - EEPROM communication error
Replace ERC
F1 E1 - EEPROM checksum error
Replace ERC
F1 E2:7 - UL A/D errors
Replace ERC
F1 E4:2 - Model ID error
Reinsert keytail.
F1 E6:0 - Latch signal mismatch error
Replace ERC
F2 E0:4 - Shorted key error
Replace keypad assembly
F2 E1:3 Keytail unplugged
reinsert the keytail
F3 E0:5 Top oven sensor open
Test and replace top probe.
F3 E1:6 Top oven shorted
Test and replace temp probe
F3 E2:9 Bake range over temperature
Test and replace temp probe
F3 E3:8 Clean range over temperature
Test and replace temp probe.
F3 E4:10 Bottom oven sensor open
Test and replace temp probe
F3 E:15 Bottom oven sensor shorted
Test and replace temp probe
F5 E0:14 Door switch errot
Test and eventually replace door lock switch
F5 E1:16 Door latch not operating
Test and eventually replace door latch
F8 E0:17 Refrigeration error
Test the cooling module.
PF Power failure - Does not indicate a fault.
PF occurs when power is disconnected.

WHIRLPOOL
Models SF3, 30'' and 24"

F2 - Oven temperature above specifications
Check 8-pin connector from temp. probe to Electronic Oven Control
F3 - Open oven temperature probe failure
Check wiring, replace oven probe if necessary
F4 - Shorted oven temperature sensor failure
Check wiring harness, replace oven temperature probe if necessary
F5 - Push button stuck or faulty
Check for binding of pushbuttons and control panel glass. If OK, replace touch panel
F6 - Electronic control logic error (timing)
Replace Electronic Range Control (ERC)
F7 - Electronic control logic error (lock motor)
Replace ERC.
F8 - Electronic control logic error
Replace ERC.
1helpful
1answer

GE wall oven was in self clean mode and suddenly an F2 error keeps beeping. It also flashes looked door - please help

Those are error codes which are listed in your owners manual. If you do not have the manual go to the GE web site, customer support section.
Mar 06, 2011 • GE Ovens
0helpful
1answer

F2 Failure Code after cleaning cycle on GE Double

f-2 is usually a runaway oven temp which most of the time means a bad oven sensor.try replacing this first.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/dude_653d05454b389bba

Jan 16, 2010 • GE Ovens
8helpful
2answers

Error code E2 F2

As you are aware the technical manual for your range doesn't show an error code of E2 F2 but all of the F2 codes pertain to the touchpad of the range.
Can you clear the E2 F3 by pressing the cancel button? If not, shut off the power to the range for a few minutes and see if the error code goes away. If the error code remains You should unplug the range from the wall and remove the back panel for the control area. Disconnect the ribbon between the touchpad and the electronic control, clean the end of it and reconnect it.
If this doesn't repair the problem you will need to replace the touchpad on the range. The parts diagram lists two touchpads, they are part numbers 8273575- bisque, and 8272702- white.
E2 relates to an overheating condition. Quite possibly related to your touchpad issue. I'd try cleaning the contacts and if that doesn't work...Up to you at that point!

Good luck
0helpful
1answer

Beeping with 'f2' & 'f3' message when cleaning but did not finish cleaning. Oven now cooled but still locked.

All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question%[email protected]#
0helpful
1answer

Control screen flashes F2 and F3; now oven element won't heat.

All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD).


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
13helpful
1answer

Kenmore Ultra bake self cleaning oven is showing code E0 - F2

My oven will not stay on, when started to preheat it will come on for a few seconds and they it will make a beeping noise and the codes E0 F2 will appear. The codes stay on even if the oven is off.
0helpful
1answer

Amana wall oven

Hi~ According to the manual for this oven, the F2 code signifies - high oven temperature. The only suggestion for any of the codes in the manual is to disconnect the electrical supply. It says" pressing OVEN CANCEL pad or disconnecting electrical supply may eliminate "F code". If failure continues, contact an authorized servicer.
I hope this helps. Linda
0helpful
2answers

F2 error, both ovens stopped working

F2 is a Oven temperature exceeded the clean runaway temperature (self clean only) or the cooking runaway temperature (cooking modes only)
Not finding what you are looking for?

Open Questions:

See all GE Profile Spectra JGBP90 Gas Kitchen Range Questions

GE Profile Spectra JGBP90 Gas Kitchen Range Logo

221 views

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Ismael Rodriguez...

Level 2 Expert

188 Answers

Cindy Wells

Level 3 Expert

6412 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...