Zanussi FJS1225W Front Load Washer Logo

Question about Zanussi FJS1225W Front Load Washer

4 Answers

Zanussi jetsystem Turbodry 1200

Hi Washer powers up and all leds work, but when start button is pressed, it keep blinking but dosent start. It was working fine till last week with out any issues. any help please

Posted by dayanand sastry on

  • Anonymous Jul 20, 2008

    e10 code

  • Anonymous May 08, 2009

    Hi,

    I have the same problem! Washer powers up and all LEDs work,
    but when green start button is pressed, it keeps blinking but doesn't start.

    Can anyone help please?

×

Ad

4 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi, Ive moved into a new flat, and I have a zanussi jet stream 1400 turbo dry front loader. Of course, no instructions were left on how to use it. I cant seem to get anything but soaking wet clothes, no spin cycle, and certainly no turbo dry.

Can you tell me where I could download a users manual?

Posted on Feb 10, 2008

Ad

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 183 Answers

It appears that you may have a faulty door interlock or a faulty PCB. pcb is not really a DIY job as some boards require proramming on certain versions. Regards Advisor

Posted on Aug 30, 2007

  • Julie J Jun 05, 2013

    Hi - I have the 'not starting' problem. The door lock is working fine and I am thinking that it is an electronic fault. I had a leaking roof recently. Could this have been caused by water damage?

×

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

My TurboDry 1200 Switches on... Takes in water... then more water.. then more water..

It then Trows the message E10.
If I bypass the Wash cycle and Spin, then Dry, it works perfect..

Any ideas?

Posted on May 11, 2010

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

The washaing machine works but the dryer doesnt wht do i do?

Posted on Oct 29, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3helpful
1answer

Zanussi jetsystem turbodry 1600 wjs1665 w is not heating the water

More than likely the heater element has failed.
This is located at the rear of the washer drum.
It means removing the rear half of the cabinet to access it.

0helpful
1answer

The drier won't heat up and it flashes up a number (I'll check tonight again what the number is). it washes fine but won't dry. It is a Zanussi Jetsystem Turbodry 1200.

Hello,

Have you fixed the problem yet? And if yes, how??
I have the same washing machine with the same problem. So I hope you can help me!

Best regards,

Nourah van Leeuwen
1helpful
1answer

Zanussi jetsystem turbodry 1200 door wont open

its the doorcatch,turn power off, remove lid and put hand in machine where doorlock is situated feel about and try open catch, repair or replace?
3helpful
1answer

What is E 40 on Zanussi Turbodry 1200?

E40 indicates the doors not closed properly. Sometimes it can be the lock itself or the main control board
1helpful
1answer

Zanussi Turbodry 1200 spin problem

if this washer is used alot then it will more then likely be the carbon brushes which u will need to take the lid off undue 4screws out where it joins front to the back screws at the back to the bottom and 1screw either side of the bottom where the panels join together behind a little cap which will have an hole in the middle of it to get it out u will then be able to get to the motor to replace the carbon brushes
1helpful
1answer

Zanusssi jetsystem turbodry 1200

clean out filter, door bottom right, unscrew filter and clean it
0helpful
2answers

Zanussi WJS 1397W

possibly a foreign object in pump.
tilt backwards at a good angle and remove pump. i find the easiest way to do this is to undo the 3 screws round the periphery of the pump
9helpful
2answers

Zanussi Turbodry jetsystem 1200

hiya
e90 means there is a communication error between the circuit boards inside. remove the plug then take the lid off the machine, remove the block which has the 5 (iirc) blue wires in it and give it a quick squeeze then replace, this should hopefully solve your problem.

hope this helps

please dont forget to rate the helpfulness of this reply, thanks kj
0helpful
2answers

Zanussi jetsystem Turbodry 1200

replace the circuit board
Not finding what you are looking for?

3,236 views

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85240 Answers

sheakhly

Level 1 Expert

34 Answers

mark warfield
mark warfield

Level 3 Expert

453 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...