My mp has a pic of a circle with xx( in it then it has a bug when i turn it on then it turns off again do u know whats wrong with it, it all started when i was listening to it and it just turned off please help. you can reach me at [email protected] thanx

1. Turn the unit on
2. Press the OPEN/CLOSE button
3. Press CLEAR, 1, 4, 7, 0, CLEAR - "TEST MODE" will appear on the display.
4. Press UP; "00 XX" (XX is a numerical value) will appear on the display. The first two digits are incremented by one, every time you press UP
5. Press the UP key until you see "12 XX" (default is 24) on the display
6. Press 2, 3, ENTER
7. Press UP key again and you will see "13 XX" (default is 23). If it does not say "23", press 2, 3 on the remote and then the ENTER button
8. Press the UP key again and you will see "14 XX" (default is 01).
9. Press 0, 0, ENTER
10. Press RETURN
11. Press CLEAR twice
12. Press RETURN ("END" should appear on the display)
13. Press OPEN/CLOSE

amitchhab276:

From the user manual for your DSC-T5 (click here), that error message means:

E:61:xx E:91:xx
A camera malfunction has occurred. Initialize the camera (page 52), then turn the power on again.

From page 52: After you have cycled-power, you need to go to the Setup1 screen and select "Initialize" and choose "OK" with the up arrow and then press the circle button. Again press the up arrow and circle to select "OK" to reset the camera to default. settings.

Make sure that the power is not disconnected during reset!

when it starts doing that hit the start button again then wait a few sec.

Hi there it is ink error.
You can try to reset the cartages this may do it Please call back let us know if it worked for you, PLEASE.

But some time when you get the chance do clean the waste tank out.
?

1. Start with printer off


2. Press and hold resume Button (triangle in the circle) and click "Power" button. Green led should be on


3. While holding the Power button, release the Resume Button.


4. Without releasing the Power Button, click "Resume" button for two times and release Both Buttons.


5. Click "Resume" for four times then soon click "Power" button, to confirm the selected action (reset counter absorber).


6. Turn off the printer and turn on again

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

This means that your unit is defective and is no longer working. The hard drive is bad.

I have bought 3 of these players. All of them worked for a while then had the eventual face/bug on the screen after turning the unit on. When the customer service number DID work, they said that the unit was defective and to return it to the store and get another.

This happened to me, like I mentioned, with 3 different units.

At first install the CD to your PC. Then connect the printer with data cable. Power on printer. Then go to your desktop & open MP NAVIGATOR .Then select SCAN/IMPORT>Open scanner drive>SCAN.

..its instruction how to reset a canon pixma 145

just wait for the bateery to die out then charge it and after that turn it on again

Hold in the play button until red light comes on, once you have the MP3's on the device, press the play again to start the audio

Turn the player on and open the disc tray. Press [CLEAR] followed by [1][3][6][9] and one of the keys [0]...[8] corresponding to the region you want to set the player for (1 for Region 1, 2 for Region 2 and so on, press 0 for Region 0 or Region Free). Turn the player off then on again for the changes to take effect.

To verify the region code, press [SETUP] followed by [1][3][7][9]. A screen will then pop up with the firmware info and the current region code setting. Using [SETUP][1][3][6][9] did not work for me.

Or
To modify the region, turn on the unit and open the disk tray. Using the remote, press [CLEAR][1][3][6][9][zone code] and cycle power on the unit (not necessary to unplug the unit, simply use the front left <POWER> button. Example: Turn on; open tray; [CLEAR] [1][3][6][9][0]; unit OFF, unit ON and you'll get a zone free DVD player.

To confirm the zone code, turn on DVD player, (unit may or may not have a disc, check that the disc tray is closed, and press [SETUP][1][3][7][9]. You'll have all the firmware information (Version xx.xx.xx.xx SUB-VER xx.xx.xx.xx;
8032 xx.xx.xx.xx; Servo xx.xx.xx.xx; RISC xx.xx.xx.xx; DSP xx.xx.xx.xx; Region Code 0) That's that final "0" that you are looking for!