Cell Phones Logo

Question about Sanyo PM-8200

7 Answers

Keys dont work on phone

Keys dont work i juat wanted to know how to take a part with out force or breaking phone case.. any help at all thanks

Posted by Jose Pereira on

  • Anonymous Nov 20, 2007

    I have the same issue. At first only some of my keys didn't work. But now the END button doesn't respond and I can't turn the phone back on.

×

Ad

7 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Nokia 6500s-1 key pad of phone is not working at all. The only key that works is the on/off switch key, there after unable to access the phone

Posted on Jul 13, 2009

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

What does that mean?

Posted on Jul 11, 2008

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Thats is very simple try to open your phone you need to use the t6 screw.if you open then you'll see the keypad flexer you need to pull out and try to back again thats all if not function you nid to buy new keypad

Posted on Aug 13, 2007

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Dear. dear if ur 6600 key pad is not working if all are not working then u have to raplace both key pad ic located on both side of keypad connector.if only one or two key are not working then it is prob from keypad wash the contents of keypad with CTC or any approved chemical.It might also be possible that the connection of kepadcable is cut of check for connection only if some keys are not working.

Posted on Mar 10, 2007

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just rub the keys with the help of rubber or scracth it with twizzer or blade.

Posted on Mar 10, 2007

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Unscrew the antena, then there are 4 screws 2 at the bottom 2 under rubber buttons at the to of the phone, just pry the buttons off with a small screwdriver, then use that small screwdriver and gently release the 2 tabs (1 on each side) about half way up. After you get it apart, gently, usung your fingers pry the chip off of the board, then the two buttons on each side, carefully slide the sides out of the holder.

Posted on Mar 08, 2007

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Chk any key short or not

Posted on Oct 26, 2006

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Model MC-UG302 upright cleaner. I need to replace power cord. How do I remove the case, I have taken out obvious fixing screws, but the casing is still not moving, I dont want to break it if I force it...

I have a similar vacuum. You literally will have to flex/pry carefully to separate the plastic shroud (Horizontal part from the upright portion. Then you can remove the panel covering the motor, trace the cord to replace. Have done that several times. When you do, you might want to purchase the long industrial cord for future convenience.
1helpful
1answer

My (older) TravelMate 212TX has problems with some keys from the keyboard. I found links that it had to do with the battery and adapter: Disconnecting the adapter and then dismount the battery would...

this at a basic level is more likely to be due to someone spilling a cup of coffee over the keyboard,In which case try to remove ,gently and clean under the keyboard,Wash plastic parts in a weak solution of detergent and replace .dont force any keys or they will break
0helpful
1answer

I wanna keep lock code in my cell phone nokia n73 but the problem is i dont know the code i have tried 12345 but then also its giving the error as a wrong code i wanna reformat my cell and want to keep...

Hey welcome to fixya. Hope u 'll be fine
  • Fixya provide u explained and good solutions Just Open the following link and follow the steps carefully to know your code.
  • For link
    Just "Click Here"
If u not want this then u can also format your cell
u don't need to unlock, for format your cell just follow following procedure
First of all Switch off your phone then press and hold 3 keys combined
  • Green dial key
  • Star key no *
  • No 3 key on keypad
then press the power on to switch on the phone.
  • In the process don't leave the 3 press and hold keys, After some time the phone 'll format completely
Note :all your data will be delete in the process of formatting.

select any solution u want
I hope this solutions will work and helpful 4 u. Best of luck
Please do rate if it is helpful
THANKS
& keep using fixya
2helpful
1answer

My scroll lock wont work and i dont know how to make it work

Press and hold the Fn key while pressing the scr lck key. Notice that the Fn key and the alternate keys have a different color (usually blue).
0helpful
1answer

Phone

Daria,

Try taking the battery out of the phone for 5 minutes. And then put it back in and try again.

Crayz
0helpful
1answer
1helpful
1answer
0helpful
1answer

Keys wont work

send it back under warrantee. I had the same problem and let them fix it. They'll have a new phone to you in 2 days and they'll save your contacts and put them on your new phone. Let me know how it works out.

Cindy
Not finding what you are looking for?

523 views

Ask a Question

Usually answered in minutes!

Top Sanyo Cell Phones Experts

Muzahura Frank

Level 3 Expert

2071 Answers

Filipe Polido
Filipe Polido

Level 2 Expert

124 Answers

Joseph Hoffmann

Level 3 Expert

1756 Answers

Are you a Sanyo Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...