Power supply gone bad

Our Canon DR-9080C scanner took a dookie, it would seem. She's plugged in, but won't turn on. I tried multiple power cords, multiple outlets (the outlets have power). Do these things have internal fuses? Could it be the power supply? Are these things known to crap out unexpectedly?what should I try next? Should I dump my coffe on it? Any info would be greatly appreciated.

Eric7 Sep 27, 2008

[080927] I have the same problem, I usually left my DR-9080C on power all the time for about 9 months now. I bought it used on Ebay in dec07'. Suddenly the unit was dead. I'm a little bit of handyman and the power board is easy to take out of the unit. Now I just need to find a place where I can get a working power supply board. The Part Number is MH3-2055. It seems to be designed to be used on multiple CANON products.

1 Answer

Mohan Sriraman

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.
Expert
490 Answers

Canon 9080C is a very good scanner, so dont dump it.

Yes all power supply units have a fuse. Check if it is okay. You can source scanner power supply board from the market, if you can handle it or it is easy to call Canon support and get it fixed.

Posted on Jun 23, 2008

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

2answers

Set up disk for canon DR 9080 path through scanner

Hi Joseph, you should be able to find the driver for your OS on the Canon website here. imageFORMULA DR 9080C Color Production Scanner

Read full answer

Apr 10, 2014 • Canon DR-9080C Path-Through Scanner

0helpful

2answers

Failure in initialization of Scanner. Scanner is offline or , scanner is turned off.

First check if the scanner is working in 'offline' mode by 'counting' a few pages.
Connect to the comp, if SCSI is the interface, you need to start the scanner first, if USB you can connect the scanner even after comp powering on. If the scanner is not recognised, reinstall driver software and scanning software.
S. Mohan, Chennai, India

Read full answer

Dec 21, 2010 • Canon DR-9080C Path-Through Scanner

1helpful

1answer

Paper tray at front of scanner will not lift. Scanner has been reset multiple times and computer rebooted as well. Error msg= unknown error canon DR-6080/7880/9080C driver versioin 1.3.10502.17001 (-4523)

Disconnect the scanner from the Comp, Try 'page counting'. If the papers go through, then you know feed mechanism is okay. if the tray is not lifting, then you have a problem. Use Qumatool software and check if the tray is lifting. If the scanner tray if lifting then the motor is okay, if not, the lifting motor may need a check.If the motor is okay, but tray not lifting means the sensor in the paper tray is faulty. Check this out.

S. Mohan, Chennai, India

Read full answer

Jun 30, 2010 • Canon DR-9080C Path-Through Scanner

0helpful

1answer

New laptop doesn't have disc drive to install my software properl

sounds like a compatability issue

Read full answer

Oct 14, 2009 • Canon DR-9080C Path-Through Scanner

1helpful

1answer

We recently acquired a Canon DR 9080C Scanner and purchases and installed a SCSI card in an older HP Pavillion. The scanner works fine using the USB port, but when using the SCSI port I get an error when...

CapturePerfect ver 3 is on chargeable basis! You can download ver 2.0 from http://software.canon-europe.com/software/0022439.asp?model= Though this is listed under Canon DR 5020, it works fine with DR 9080C. DR 9080C has very intelligent features and ver 2 works fine. I do not know if there are addl features with ver 3.0. I have used for scanning over 500,000 docs.
S. Mohan

Read full answer

Aug 05, 2009 • Canon DR-9080C Path-Through Scanner

0helpful

1answer

Canon DR-9080c scanner power supply

The scanner technicians and ScannerSolutions.com can help you solve this problem. As an Authorized Canon Scanner Repair provider they have access to official repair manuals and carry an extensive parts inventory. You can call them at 877-705-7226 for assistance. Ask for Ryan Wilson.

Read full answer

Jun 01, 2009 • Canon DR-9080C Path-Through Scanner

1helpful

1answer

Canon DR-9080c scanner power supply

There should be cables connected to CN1 and CN6. CN3 is not shown on the circuit diagram in the service manual.

Read full answer

Apr 28, 2009 • Canon DR-9080C Path-Through Scanner

0helpful

1answer

Ink for Canon DR-9080C

Its a scanner not a printer!!

Read full answer

Aug 08, 2008 • Canon DR-9080C Path-Through Scanner

0helpful

1answer

Need CapturePerfect 3 driver for Canon Scanner DR 9080C

I have the same model Canon DR-9080C scanner which I recently acquired and I'm trying to figure out how used it is. I see many referrign to a counter. I see the big LCD on top front, but how do you know how many total pages have been scanned through it? I read somewhere there is a mechanical scanner. Is this true?

Read full answer

Jun 28, 2008 • Canon DR-9080C Path-Through Scanner

0helpful

1answer