Error 6 & 8

The error code 83c00020 appears when the printhead of the system fails. Fix the error by resetting it and changing the printhead of the printer. Follow the steps below to fix it.
Step 1: Turn on the printer and remove the power cord from it.
Step 2: Leave the printer for 60 seconds.
Step 3: Connect the power cord back to the printer.
Step 4: The printer should turn on automatic
Step 5: If the printer does not turn on automatically, then do it manually.
Step 6: Open the cartridge access door.
Step 7: Remove the printhead out of it and keep it aside for recycling.
Step 8: Buy the original printhead accessory from the HP website.
Step 9: Replace the printhead and close the cartridge access door.
Step 10: Following the above steps should have fixed the error.
For Support Call Our Toll-Free 1-866-293-9220

HP LaserJet M1005 MFP - Scanner Errors 6 and 12 Solution ISSUE: The scan head may not be in the correct starting position.
Updated firmware is available to resolve the issue.
SOLUTION: Upgrade to newer firmware (version20120831 or newer) available on hp.com Support & Drivers.
Select Drivers & Software, enter the product name/number, select operating system and locate the firmware download.

that is mean that you have a problem with the fussier , first open your machin with press 0+8 then press 400 start entarrabt if that don't help you so If you can check the fussar

remove the network card at the back, re-insert or replace it...

1. If you have the disk then put the disk in and close the installation window that comes up automatically 2. Go to computer, right click on the disk icon that shows there and click on explore 3. Go to util>ccc and click on uninstall_L3 4. Restart your computer 5. Download the latest version of the adobe flash 10k (www.adobe.com) 6. Start installing once again and complete the installation 7. If the installation doesn't completes then let me know 8. If completes, try to scan, it should scan but if it doesn't then 9. Download the utility from the link given below and check where the error lies http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=oj-86374-1&lc=en&dlc=en&cc=us&os=4063&product=3737195&sw_lang=

You got the answer for the solution, call the customer care and tell the error code they will tell the solution in the phone, if not they will send the technician to sort the problem

Thank you.

The error message "83.0180" shows that an EIO error has occured.
Perform the following workaround and see whether the issue still persist.
1. Ensure that the printer is connected directly to the wall outlet.
2. Turn off the printer and then power on and see whether the issue persist.
3. Reseat the Jetdirect card and see whether the issue still persist.
4. Reseat the jetdirect card on a different slot and see whether the issue still persist.
5. Remove all the accessories from the printer and then power on the printer. See whether the issue still persist. If the issue does not persist, add on the accessories onee by one.
6. Power on the printer and check whether the issue persist, each time an accessories are added.
7. Swap the Jet direct card with a known good jet direct card and see whether the issue still persist.
8. Perform a cold reset and see whether the issue still persist.
To do a Cold Reset:
1. Remove all cables.
2. Press & hold the Test button while applying power & continue to hold it for 10 seconds, then release it for 10 seconds, then unplug it again.
3. Connect all cables & power it back up.
4. Wait 2 minutes for discovery & DHCP. If desired, change the DHCP & address settings.

Hello. You probably have a worn out trailing cable. The manual says:

System Error: 010036 (see next page for 010036 0000XX00)
Problem Description: ADC Test Failure in the Main PCA.
Corrective Action: Try the following:

Switch the Printer OFF from the back and
then disconnect the Trailing Cable from the
Electronics Module. Switch the Printer ON and
see if the Error Code now changes to “010037”.
If the error code remains as “010036”, replace
the Electronics Module �� page 8-6.

If the Error Code changes to “010037” then try
the following:
Make sure that the Trailing Cable is
connected correctly.
Replace the Trailing Cable �� page 8-36.
Replace the Carriage Assembly �� page 8-42.

The manual can be downloaded at: www.lpscomputer.com/ec/manuals.htm

Hi,

Please uninstall the current PCL driver and upgrade the same with UPD PCL5 (dont install PCL6) from http://www.hp.com/go/upd

Regards,
Nikhil

so, just enter 10871087, press start, after enter 163, press start. thats all.