Question about GE Profile JTP56 Electric Double Oven

Error message An error 3 message appeared in the middle of cooking, and now nothing works but the clock. You can't turn the oven off, on, or do anything at all.

1 Answer

Ron Marek

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.
Master
878 Answers

Webgenie, the code should read F3, which indicates a open oven sensor (over 2900 ohms). The sensor should ohm out at 1080 ohms at room temp. Best thing to do is replace the oven temp. sensor. Easy job..Catriver..post back.

Posted on Sep 25, 2006

1 Suggested Answer

6ya staff

2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

Upload

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Why does Neff. U1661 show "err" error message?

temperature ntc failing will need replacement.

May 19, 2014 | Neff U1661 Double circotherm super...

1 Answer

Frigidaire f5

Hell Gina, thank you for your inquiry!

I understand you have already tried resetting the range. It is important to wait roughly ten minutes and then turn the unit on. Since the error code F5 reappeared, it typically indicates a communication error between the power board and UIB (user interface board). In this case, I would recommend reaching out to an expert technician to ensure the appropriate replacement part is order and installed correctly to prevent future issues. I hope this information helps to some degree - thanks for your question, and please do not hesitate to reconnect.

Sep 06, 2013 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

I was getting a small "0" error message on the display of my Miele dg 155 steam oven. Tried Descaling but the process didn't complete, stopped at 10 minutes (33 minutes total) and started...

GO TO SERVICE MODE. TURN OVEN OFF OPEN DOOR MOVE KNOWB COUNTER CLOCK WISE TO DEFROST PUSH TEMP BUTTON 3 TIMES PUSH + BUTTON TILL YOU REACH 67 CLOSE DOOR AND WAIT FIVE MINUTES VOILA......

Feb 26, 2011 | Miele DG155-1 Steam Oven Single

2 Answers

I have a frigidaire m/n PLES389ECD and the burners and oven aren't working and had the error code f20, the clock timer was replaced but now the clock is the only thing working the burners and oven still...

The ESEC system and the electronic oven control ain't communicating. Check the wiring connections between the oven control and the esec controls. The thang is designed to lockout the top burners while the self clean feature is in use. If you failed to reconnect that connection which feeds back to the ESEC I imagine nothing does work. LOL. here's a video which shows how it works and I have the manual loaded on Gdocs fo you.

30 Inch Freestanding Electric Ranges_Rev A (5995438461).pdf (4 megs) printable.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Dec 31, 2010 | Frigidaire Ovens

2 Answers

We turn oven on to heat and get E2 error code and then F1 error code where cook time should be displayed

Hi dear.Here is what you can do: F1 - E2
UL A/D error(s)
1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock).

I hope that helps.Thanks

Aug 31, 2010 | Whirlpool 30" Self-Cleaning Freestanding...

1 Answer

Self-cleaning oven F2 error message

Well I found three all same series... If it's occasional I'd leave it 'till was always on? Anyway .....
F2 - E0 Shorted keypad Replace Electronic Range Control/Clock (ERC)
OR....
F2 Oven temperature sensor shorted Replace oven temperature sensor
OR

F2 Temperature runaway detected (Bake/Broil: 600 - 700 F; Clean: 930 - 1000 degrees F). Sounds alarm and resets to non-cook mode. Check relay board for stuck contacts. Check oven temperature sensor for normal room temperature resistance (1085-1097 ohms at 75 degrees F). Check sensor wiring connectors for a loose or high resistance connection. Check electronic range control (also called clock or ERC) functions Replace relay board if necessary. Replace oven temperature sensor if other components check normal. If failure repeats, replace electronic range control (also called clock or ERC)

Feb 16, 2010 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

I was cooking in my Kitchenaid oven and the door locked. It will not unlock

We had the same thing happen

Turn the oven breaker off, then let the oven cool completely. Turn breaker on, there will be an error code appear, push and hold the "bake" button for at least one minute until an error message appears, then press the off button.
This reset the latch on our oven

Nov 02, 2009 | KitchenAid Ovens

1 Answer

F3 & F1 Errors & oven shuts off

Concerning the F3(Open or shorted oven temperature sensor (RTD)

Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.

Concerning the F1(Stuck touch pad)

Usually means that either the touch pad or the oven control (also called clock or ERC) is defective and needs to be replaced. If this fault code cannot be cancelled, replace the oven control (also called clock or ERC), touch pad, or both.

Jun 02, 2009 | GE Ovens

1 Answer

F3 and f5 error codes on maytag gas wall oven

(((F-3)))

This is a Shorted or open oven temperature sensor (RTD). Check the following.

Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.

(((F-5)))

This is a Watchdog and hardware conflict.

This is not repairable. you will need to replace the control board or (erc)-(clock)

Feb 24, 2009 | Maytag 24" Built-In Single Gas Wall Oven -...

2 Answers