Auto Setup [set] -> Enter

While the set is on, pull the power plug. Then hold and depress the power button in for about a minute. Then replug set and turn it back on. If that does not reset the tv then you do indeed have a serious issue with the set.

Just contininue to try that it if not then you'll have to do a hard reset.

1. Press TV to select the TV mode.
2. Press POWER to turn on the TV. The STARTING SETUP function
begins and the language setup menu appears on the screen.
Press upArrow (^) or downArrow (v)to select your desired
language, then press ENTER.
3. Press (^) or (v) to select TV or
CABLE, then press ENTER.
4. Press (^) or (v) to select START, and
then press ENTER, which
starts the AUTO SETUP.
Note:
To cancel the setup and return to the regular TV screen, press (^)
or (v) to select CANCEL and press ENTER.
5. When the AUTO SETUP is complete, the regular TV screen
appears.
Notes:
• AUTO SETUP of channels may take 15-30 minutes to complete,
depending on your regional cable service.
• To cancel the AUTO SETUP and return to the regular TV screen,
press EXIT.

from TV manual that uses a CT885
http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=4&ved=0CEcQFjAD&url=http%3A%2F%2Fwww.hdtvsolutions.com%2Fpdf%2F50hp66_om_e.pdf&ei=_KppUvWPNqjSyAHTr4DIAg&usg=AFQjCNGar3aphbJ5yNHl9QMUJsSI6SjCTQ&bvm=bv.55123115,d.aWc

hi,
you reseiver is now in stereo mod that's why there is no surround and center. its some thing related to to the setting in the receiver or in the blue ray.

Settings in blue ray player
First of all check the audio settings in your blue ray players audio setting.
You didn't mentioned the brand of your blue ray player. Anyway go to its setup and set the audio output priority as HDMI. also turn OFF the DRC if its a sony blue ray player. Also check the down mixing setting make it satandard

Settings in receiver.
First of all check the surround settings.
Play a blue ray disk and press the STANDARD button o the receiver's remote and select STANDARD mode.

If you didn't get the surround channels follow the below procedure
Now go to the setup of your receiver.
1. Using the down arrow go to the Advanced play back and press enter.
2. In the Advanced playback menu select auto surround mode and press enter
3. Select it ON using right arrow or left arrow. and press enter
4. Exit the setup and check is every thing working fine.

If dosn't work
Again go to the setup of the receiver
1. Using down arrow select Speaker setup and press enter
2. In the speaker setup menu select speaker configuration and press enter
3. Check the status of all the speaker, if any speaker is in NONE position , make it LARGE or SMALL according to the speaker you are using.
Exit setup and check again.

If you need any more assistance feel free to contact me through fixya.

regards
Ajin

hi,
u cam reset ur only by the following way.

p { margin-bottom: 0.21cm; }

In order to enter Service Mode, TV guide must be turned off

In order to do this procedure you must have and use the correct remote. The full function remote that

came with the set has a TV Guide Logo in a red box. This is the remote you should use.

NOTE: If TV guide has not yet been setup, then the 1st step is to follow instructions to set TV guide up.

Enter ZIP code, cable or ant. Etc.

1.press and release the "TV Guide". TV guide will appear on the screen.

2.Navigate to the TV Guide tool bar and use the ">" button to select "setup" in the menu and press

and release the "enter" button

3.use the "arrow down" button to select "default options"

4.press and release the "enter" button and select "general defaults"

5.press and release the "enter" button (opens menu on lower left side)

6. use the "arrow down" button to select "auto guide"

7. use the ">" button to select "off"

8. use the "arrow down" button to select "done"

9. press and release the "enter"

10. press and release the "TV Guide" button to turn the display off

System Reset Using Service Mode:

1. Enter Service Mode

2. Use the "muting" button to select "initialize" screen

3. While on the "initialize" screen

4. Use the "down arrow" button to select "final setup"

5. Press and release the "enter" button to select "data reset"

6. Use the ">" button on the remote to select "yes"

7. Press and hold the "enter" button until the screen goes black release "enter" button on remote.

8. Power the unit off using the remote control

9. Unplug the power cord from the media receiver to complete the reset

10. Plug in the media receiver; turn the system on and reset is complete.

ok

Access the system setup of your tv using the remote and switch off auto programming.

i would suggest cycling thru the inputs- av1 av2 rgb hdmi. blue screen is indicator of no input.

I had this same problem (DVD1). Resolved as follows: With DVD player on, pointed remote at DVD player, pressed and held the 1 key and then pressed and held the enter key (both at same time) until I saw the DVD1 on the DVD player display disappear. Now everything works.

I purchased this same unit yesterday from the PX Power Zone. I hooked up the unit and even managed to record a few minutes of a show. I then went into setup and made a few changes. Now, I have no display at all from the unit. Does anyone know how to reset the unit back to factory settings? Please email me at [email protected]. Many thanks!

Bill

Try this (with the original remote): Reset TV Guide On Screen
1. Press the TV Guide button
2. Curser up and over to the SETUP menu
3. Select Change system settings (highlight only)
4. Enter the following numbers … 753159852 (setup mode)
5. Enter the following numbers … 653274147 (reset mode)

It will take some time to get the guide downloaded, but it works.