Question about GE Profile Prodigy WPSE4200A

Will not drain during spin???

I have a GE Profile Prodigy. Purchased used. All cycles work. But it wont drain during spin. The clothes at the bottom are still soaking wet. Any suggestions? All help is most appreciated. Many, many thanks to the one who solves this problem.

Anonymous Nov 12, 2007

We have had the same problem. We checked filter and we had repair service come. He suggested buying a new pump. we did that installed it and problem persists. However, try the quick cycle under "other cycles" Tried that today and it is working. It drains just fine, which would indicate that it is a computer issue-stick with turn dials- forget the computer screen appliances- too many bells and whistles and they break down. And don't buy this washer! The washer is only 2 years old and was expensive. VERY annoying.

1 Answer

prem mathew

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.
Master
1,294 Answers

Most likely your outlet filter of the machine is choked with dirt or something; clean out the filter & refit. Of course after taking of the wall plug & siphoning out the water from washer.

Posted on May 13, 2007

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Spin cycle stops and moter humms

clean the filter out may be clogged

Jun 16, 2012 | GE Profile Prodigy WPSE4200A

1 Answer

Wont spin and makes alot of noise

You could check if its drum by removing the belt turn drum by hand if its okay no noise check motor pulley ....is motor ok ?

Nov 17, 2009 | GE Profile Prodigy WPSE4200A

1 Answer

I have a GE Profile Prodigy top load washing machine. Sometimes the spin cycle does not spin, sometimes it spins. It makes a clicking noise during gentle cycle

The gears maybe going out. Sometimes it is able to engage in the other direction which the spin, sometimes not. Washing machine have complex gears that in one way agitator works, and the other the gear locks to turn the whole tub. The clicking noise is probably the locking mechanism in the gears that has caused the whole intermittent problem.

Jul 01, 2009 | GE Profile Prodigy WPSE4200A

1 Answer

Ge profile prodigy make clunking before spin cycle

Is there a humming sound? Check you have the hot and cold water supply turned on. Check the water inlet hoses are not kinked.

May 03, 2009 | GE Profile Prodigy WPSE4200A

1 Answer

Washer will not agitate or spin

HI,

you can view this site to have some ideas about your agitator problem.

http://sites.google.com/site/sublimeappliancerepair/washer-will-not-spin/agitator-woes

any further question let me know.

thanks,

Mar 29, 2009 | GE Profile WPRE6100G Top Load Washer

2 Answers

Ge washer # WBVH6240FWW

We have a GE washing machine that works fine with no load, but will not finish the cycle with a full load.

Aug 15, 2008 | GE Profile Prodigy WPSE4200A

1 Answer

GE Profile Prodigy filled with water & won't start

If you don't hear a click when you close the lid, replace the lid switch.

Jan 29, 2008 | GE Profile Prodigy WPSE4200A

1 Answer

Spin and Agitate problem on GE Profile Prodigy WPSE4200A

This machine uses an electric water pump. I would check to motor. Remove the front panel and operate the machine to see if the motor is working. Check this by listening to the motor and watching the belt. If you hear the motor but the belt does'nt move then there may be a problem with the pulley or motor clutch assy.

As far as not draining or pumping water ? Check the wiring from the pump to the control panel. If these wires are alright then i suspect the pump.

Nov 15, 2007 | GE Profile Prodigy WPSE4200A

2 Answers

GE Model WHDSR209D2WW makes unbearable loud metal Screeching noise

ppr78, couple of things you want to check. The bottom panel on these GE's are pretty flimsy. I have run into a couple where during agitation the bottom of the motor housing would rub against the bottom panel making a terrible noise. You need to remove the front panel by pusing on the clips on the left and right side just under the top. The front panel will pull out. During agitation, take your foot and push down on the bottom panel and see if the screech goes away. I have also found the suspension rod support sockets at the top dry out and make a screeching noise. You also want to check your belt and pully and see if the noise is from there. Check these things first...Catriver..post back.

Jan 12, 2007 | GE Profile Prodigy WPSE4200A

1 Answer