Pioneer PureVision Pro-1000HD 50 in. HD-Ready Plasma Television Logo

Question about Pioneer PureVision Pro-1000HD 50 in. HD-Ready Plasma Television

1 Answer

Screen pixels out.

After viewing my HDTV for about 30 minutes the top area of the screen pixels out. If I turn it off for a few minutes the picture will be ok but the problem occurs again. The HDTV is four years, is the TV about to go out or can it be fixed? I have read the troubleshooting guide but there is no topic on the owner manual for this problem.

Posted by Rene Carsner on

Ad

1 Answer

Anonymous

My problem has being taken care. The circuit board was replaced and that took care of it. The cost $1,500.00

Posted on Aug 08, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Horizontal lines shadowed / blured picture after 20-30 minutes

There are some semiconductors or capacitors that are leaky. Might need thorough check up inside the TV.
0helpful
1answer

Dead Pixels on Sharp Aquos 70" LED TV

If pixels are gone on all channels - Exchange it
Can't fix it yourself unless you are tv technician
It is quite common for few pixels to be dead but that is usualy not noticable
1helpful
1answer

My Toshiba 46XV540U LCD TV. Has ghost image plus many white vertical and horizontal line when it is turned on. These lines and the ghost image stay for 20 to 30 minutes and than the picture becomes clear....

Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish board that call T-CON board to do a replacement.This T-CON board sit in the middle at the bottom of the tv LCD screen panel.This T-CON board control all the picture pixels going throught to the tv LCD screen panel.
1helpful
1answer

DP42647 On half of our 47 inch screen it is black and distorted when we first turn the TV on but after 30 or 40 minutes it finally just lights up and is fine.

Tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish board that call the T-CON board for the replacement.This board sit in the middle at the bottom of the LCD screen panel.This T-CON board only job are to decodering picture pixels dots only before it show up to the LCD screen panel.
1helpful
1answer

Bottom half of screen goes black

This is because full pixels of your TV is not getting invoked at the beginning .If you are able to view the picture as normal after 1 or 2 minutes, its fine.Else you need to call to service center and get this problem fixed.
0helpful
1answer

Flickering Pixels on Plasma

The top y drive cable is loose or dirty. Delicate job to fix.
0helpful
1answer

Flickering/pixelating screen on LTV-27w6 HD after 30 minutes.

Sound like dry goint on Power Supply bord. I had the same problem and resolder most of the parts of the power supply and TV was ok.
2helpful
1answer

Hisense 42in plasma flashing blue/green pixels after 30 mins

Do a master reset
1. unplug the TV from the wall
2. remove the batteries from the remote
3. wait 24 hrs
4. plug TV into the wall socket
5. install batteries in remote
6. hold power on button for minimum 10 seconds
This was given to me by the Hisense service line and worked for my TV.
Not finding what you are looking for?

Open Questions:

139 views

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76851 Answers

Jaime Hernandez

Level 3 Expert

2343 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...