Ricoh Aficio 450 Copier Logo
Jon Hyland Posted on Feb 28, 2012

Ricoh sc 672 error on new machine

Please wait for extended time then SC 672. Have tried another HDD, reseated all connectors on control board and control panel as well as checked all other connectors. Tried reloading firmware thru sd card and didn't recognize the card. tried booting with HDD disconnected and still codes out with SC 672

  • 2 more comments 
  • Jon Hyland Feb 28, 2012

    Cannot go into service mode at any time either

  • Jon Hyland Feb 28, 2012

    This is a MP6001 B?W machine

  • adongo noble Nov 07, 2016

    My richo aficio mp 2510 copier displays error code sc672. How can. I fix this?

  • Tha Make Nov 02, 2019

    Cheng contoler

×

1 Answer

Manzoor Ahamed

Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Welcome Back:

Visited the website for 2 consecutive days.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 13 Answers
  • Posted on Feb 29, 2012
Manzoor Ahamed
Contributor
Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Welcome Back:

Visited the website for 2 consecutive days.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Jan 02, 2012
Answers
13
Questions
0
Helped
46862
Points
23

  1. Go to this code with "Clear Mode"+107+"Clear/Stop" hold for 5s.
  2. Go to System Settings
  3. Go to 5875
  4. Check the setting of SP5875-001. If the setting is set to "1 (OFF)",change it to "0 (OFF)".
Try checking or changing the thermistors!
The metal contact spring on the thermistor broken causing all sorts of 'unrelated errors including 'Please Wait' sc 670 and sc 402...

  • 1 more comment 
  • shaker fadlo
    shaker fadlo Dec 13, 2014

    The machine don't respond to this code even when I restart it I don't know what's the problem My machine is Gestetner Dsm 725 It gives me this message" Functional error sc 672"

  • Anonymous Jun 29, 2017

    In mine case The only solution was to clear the NV ram sp 5-801(first backup Sp 5-824 and print smc, incl.non default sheet if possible)

  • Tha Make Nov 02, 2019

    Contorlar brod

×

2 Related Answers

A

Anonymous

  • Posted on May 05, 2009

SOURCE: sc code 672 with aficio 2090

Direct from the service manual:

• Controller board defective
• Controller board installed incorrectly
• Operation panel harness connection loose or incorrect

Ad

quennie732

  • 422 Answers
  • Posted on Nov 15, 2010

SOURCE: Problem with the Ricoh mp c2800 Ricoh error code

If the model ia a MPC 2800 it a controller board issue maybe the operation panel. -carl

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

SC 672 error apears in my ricoh 4002SP. what shal i do?

sc 672 Controller-to-operation panel communication error at startup
Possible Causes
? Controller stalled
? Controller board installed incorrectly
? Controller board defective
? Operation panel connector loose or defective
? The controller is not completely shutdown when you turn the main
switch off.
Check the setting of SP5875-001. If the setting is set to "1 (OFF)", change it
to "0 (ON)".
0helpful
1answer

ERROR SC 672 IN RICOH MPC 6000

SC 672 is a controller error. So possible is tat the controller board is defective, in best case can be only the ram memory dimm's or the HDD but in most cases the controller board is dead.
0helpful
4answers

My ricoh aficio is showing sc819

Bad hard drive? unplug it an turn on unit. -Carl
1helpful
1answer

What is error sc-672

It is a problem with the controller. Or the controller board is not installed correctly or maybe a connector is not connect correctly. It could be the controller is bad and should be replaced.
0helpful
3answers

Ricoh 3045 sc865-01 , any solutions ?

In general the SC 860-900 refer to HD acces error.
SC 865 - the hard disk detected an error.Error detected other that the bad sectors error SC 863 or the CRC error SC 864.Reset the error code by turn the operation switch and main power switch OFF and ON.Try disconnect and reconnect the hard disc connectors and verify the cable.
0helpful
1answer

Ricoh aficio 3035/3045 error sc 672 not able to proceed to service mode also, kindly help me pls.

possible a bad operation panel replace or 672 B
After powering on the machine, the
communication circuit between the
controller and the operation panel is not
opened, or communication with
controller is interrupted after a normal
startup.
Controller stall
Controller board installed incorrectly
Controller board defective
Operation panel connector loose or
defective
690 A GAVD block I2C bus error
An error is detected in the GAVD
communication I2C control register of
the GABIC2.
I2C bus on BICU defective
691 A GAVD FCI block I2C bus error
An error is detected in the FCI
communication I2C control register of
the GABIC2.
I2C bus on BICU defective
692 A CDIC GAVD block I2C bus error
An error is detected in the CDIC
communication I2C control register of
the GABIC2.
I2C bus on BICU defective
700 B ARDF original pick-up malfunction
After the
9helpful
1answer

Ricoh 1045 error code sc 672, 961

Controller to operation panel comucation error at start up.Check the controller stall,controller board installed correctly operation panel connectors.Enter im the service menu ,press the SP mode,open the front door,turn off the copier,unplugged the machine.Wait 10 seconds,plugged on the machine,close the front door,turn ON the copier and make a copy.
1helpful
1answer

In Ricoh aficio 401

The SC360 is Hard disk drive error 1. This means that the machine does not detect the connection signal from the HDD.

CHECK THESE; poor connection between the HDD and the HDD controller,
the AC power connector to the HDD is disconnected,
HDD defective,
HDD controller board defective,
BICU defective.
Make sure all connections are tight and secure, make sure power is connected securely, make sure HDD ( hard drive) is not bad if so replace. If the above are fine, replace the controller board and if the problem is still there, replace the BICU board.
4helpful
2answers

Error code sc 490 and sc360

Did you try to rest the error? Do you know how too?
Not finding what you are looking for?

43,401 views

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Cindy Wells

Level 3 Expert

6693 Answers

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...