Question about Kenmore 24 in. 15689 Built-in Dishwasher

1 Answer

Under cycle setting the quick rinse light keeps flashing and dishwasher does not run.

After the first time the quick rinse light began flashing I disassembled the door and control panel (after shutting off power). I disconnected all of the electric connectors from the electronic control. Once I reassembled the electronic control and the inside panel and turned the power back on the dishwasher ran again through about 3 loads but each time it stopped short of the final cycle and there was water in the bottom tub when it stopped. It now has stopped completely and will not run. I tried to repeat what I did earlier to bring it back to life but no such luck. I can not locate any of the manuals from 2002 when we installed it. Thanks, Jim

Posted by on

  • Anonymous Mar 23, 2014

    Smelled of burnt something after end of cycle. Now powers on to disoriented flashing lights then turns quickly off and doesnt start.

×

Ad

1 Answer

Ron Marek
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 878 Answers

Hey Jim, if your model starts with 665 there was a service flash on this unit concerning your problem. SF-22-715. Dishwasher stops in mid cycle. The control board was redesigned to eliminate this problem. The service flash states that if only one indicator light is blinking it's usually a stuck or shorted keypad. I would check with Sears and see if you are covered under this service flash. Catriver...post back.

Posted on Aug 28, 2006

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

6ya.com

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Kitchenaid Superba dishwasher model # KUDS01FKSS0 where the rinse only button blinks continuously. It won't let you cancel or run the cycle. Is this a trouble code? If so what does it mean?

our kitchenaid superba dishwasher does not work, "Rinse ...

www.appliancepartspros.com/answers-for-whirlpool-panel-cntl-8531257...
Dec 27, 2011 - If a key without a light is stuck or multiple keys are stuck, the control will flash the light for the Rinse Only/Quick Rinse key." You will also need to

Sep 27, 2015 | KitchenAid Dishwashers

1 Answer

24 in. GU980SCG Built-in Dishwasher: My dishwasher (GU980SCGB3) now stops at the rinse ...
Looks like micro controller problem. Contact service center for assistance.

May 17, 2010 | Whirlpool 24 in. GU980SCG Built-in...

1 Answer

Mdb6650aww code flash: Rinse Cycle & Wash Button.unit inoperative
You might try running the diagnostic mode which can be model dependent. To find your particular method to do this .... unscrew and remove the lower kick plate under the door. The service technician paperwork is usually taped to the kick panel or the tub or side wall. Within that paperwork should be the work process to run through the diagnostic mode. The work process is one of pushing various control buttons in a sequence within a quick time frame and repeating 2-3 times.
If that fails ... other potential reasons run the gambit of a bad control panel (or loose wire connection to the panel), bad heating element, etc
Good luck on your troubleshooting!

Jan 20, 2018 | Dishwashers

1 Answer

Quick Rinse light was flashing at end of cycle. Opened and closed door and pushed Start. Quick Rinse and Cancel/Drain light are now flashing and machine won't start. Turned off power supply (30 seconds) /...
Ok try this, open the door and then hit these buttons in the following combination. HI TEMP - DRY - HI TEMP - DRY...then close door and press cancel...then wait for the pump to shut down. you should be able to run a cycle after this...If this fails to fix the problem give me the make and model # of the dishwasher, this can normally be found just inside the door.

Jun 22, 2009 | Dishwashers

3 Answers

Dishwahser rinse cycle running for hours
Do you have high temp rinse or sanitize selected? This will pause the timer during the final rinse cycle to heat the water. The sensor might be bad. Try the quick cycle, I don't think this heats the water.

Jun 09, 2008 | Bosch 24 in. SHU43 Built-in Dishwasher

2 Answers

Kenmore Dishwasher #15769
Try this solution first
Push the Hi-temp and then push the Sani-rinse. Go back and forth multiple times on these two buttons. I found that after a handfull of pushes that a "1" came up on the display. I continued to keep rotating the two buttons and then a "2" came up on the display and the dishwater started it's "drain" phase. I then hit cancel to clear and then I selected the cycle I wanted. The washer started up just as normal at this point.

Feb 16, 2008 | Kenmore 15769 Built-in Dishwasher

4 Answers

Green clean light flashing dishwasher
press back and forth between hi-tempwash and sani rinse several times to get all lights to come on if not then press sani rinse and heated dry back and forth several times. one of though combos will start the test mode

Nov 22, 2007 | Dishwashers

1 Answer

Flashing quick rinse light on panel
I had the same problem but I found someone wh said that there is a way to reset the dishwasher. I tried it and it has worked so far.

Here is what I did.
Push the Hi-temp and then push the Sani-rinse. Go back and forth multiple times on these two buttons. I found that after a handfull of pushes that a "1" came up on the display. I continued to keep rotating the two buttons and then a "2" came up on the display and the dishwater started it's "drain" phase. I then hit cancel to clear and then I selected the cycle I wanted. The washer started up just as normal at this point.
Good luck!

Oct 24, 2007 | Kenmore 15769 Built-in Dishwasher

1 Answer

Asko 1585 Dishwasher
do they flash lik all on one side then the other? Start a cycle, then open the door. Do the lights flash the same way when you open the door as when it stops? if soyou may have a door that needs to be adjusted so it closes better. when the cycle ends, is there any standing water in the bottom? if so you may have a poorly routed drain hose or a partial clog in it. Last, pull the bottom panels off and look inside the bottom of the dishwasher and see if there is standing water down there . If ther is you have aleak somewhere or a bad drain pump. You r only other choice is a bad pressure switch. If youve already adjusted the water fil to the proper level ( just up to the grey plastic housing that the lower wash arm sits on) tehre really aernt any more options. Hope this helps!

Aug 29, 2007 | Asko 24 in. 1585 Built-in Dishwasher

2 Answers

Blinking Quick Rinse
brent, After doing a little research on this model, I see that Sears put out a service flash concerning this problem. Dishwasher stops in mid cycle and one or more of the lights are flashing. SF22-715. The correction is to replace the existing board with an updated board that controls the line voltage better. Part number 8530928. You could be covered under this flash. The tech will have to eliminate the possibility of a stuck or shorted keypad which will cause this same effect. You can try to get this back in operation by pressing in this order: high temp wash-air dry-high temp wash-air dry. This will put it into a self test mode. Just let it run through if it works. If you don't have those keys try power scour-air dry-power scour-air dry. Catriver...post back.

Nov 19, 2006 | Kenmore 16639 Built-in Dishwasher

Not finding what you are looking for?

View Most Popular

24 in. 15689 Built-in Dishwasher

  • Dishwashers

Related Question

I have a Kitchenaid Superba dishwasher model # KUDS01FKSS0 where the rinse only button blinks continuously. It won't let you cancel or run the cycle. Is this a trouble code? If so what does it mean?

  • KitchenAid Dishwashers

Open Questions:

0 Answers

Where do I get a user manual

Sep 10, 2014 | Kenmore 24 in. 15689 Built-in Dishwasher

0 Answers

kenmore quietguard 3 has flashing orange light on normal wash and wont start Will not reset or start...flashing orange on normal wash

Jul 12, 2014 | Kenmore 24 in. 15689 Built-in Dishwasher

0 Answers

why are my dishes not clean?

Jul 08, 2014 | Kenmore 24 in. 15689 Built-in Dishwasher

0 Answers

how to unlock

Jun 09, 2014 | Kenmore 24 in. 15689 Built-in Dishwasher

See all Kenmore 24 in. 15689 Built-in Dishwasher Questions

Related Topics

Kenmore 24 in. 15689 Built-in Dishwasher Logo

768 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

Kenmore 24 in. 17482 / 17484 /...

Kenmore 24 in. 15689 Built-in...

Kenmore 24 in. 15079 Built-in...

Kenmore 24 in. 17482 / 17484 /...

Kenmore 24 in. 17032 Built-in...

Top Kenmore Dishwashers Experts

vince

Level 3 Expert

1234 Answers

Israel Pineiro Jr

Level 2 Expert

165 Answers

Ron Rak
Ron Rak

Level 2 Expert

138 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...