Ramp Networks WebRamp 310e Bridge/Router Logo

Related Topics:

Herbert Haamucenje Posted on Jul 29, 2006

Webramp finder can not find Webramp

1). IP address lost Webramp finder cannot find the webramp and therefore new IP address can not be added. 2). Does not prompt for login or give the > prompt when connected via serial cable in "console mode" in order to put in new IP address. Seems to have lost firmware (if it has, how can that be fixed?)

  • Herbert Haamucenje Jul 31, 2006

    Don't crack your brains any more on this; I have resolved the issue myself by loadeding the firmware.


1 Answer


Level 1:

An expert who has achieved level 1.

Problem Solver:

An expert who has answered 5 questions.

  • Contributor 5 Answers
  • Posted on Jun 04, 2007
Level 1:

An expert who has achieved level 1.

Problem Solver:

An expert who has answered 5 questions.

Joined: Jun 04, 2007

Careful with that firmware loading! If you load too new a firmware, the webramp will ask for an "UpgradeKey", which you can't obtain because the company's out of business. Then you just have a pretty brick.

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


Asus fonnepad does not conect automatically to wifi router

1. Launch a browser and access router settings by keying in on the address bar.
2. To set up the VPN server:
1) Click "VPN Server" on the Advanced Settings menu on the left panel.
2) On the "Enable PPTP Server" item, select "Enable".
3) Select type of Broadcast Support.
4) Select type of Force MPPE Encyrption.
5) Type a range of IP addresses for the VPN clients. The example on the screenshot below shows an IP address range of "" to "".
*The specified IP address range can be from to As a VPN server, the ASUS router can assign only a maximum number of ten IP addresses.
6) Input a username and password for VPN clients. A maximum of ten usernames and passwords can be added.

Configure ip adress to hp laserjet p3015

This model does actually have embedded network functionallity.
To configure the IP Address, follow the menu map as below:
1) - (4) I/O
2) - (4-2) Embedded JetDirect Menu
3) - (4-2-2) TCP/IP
4) - (4-2-2-1) Enable (Make sure this is 'On')
5) - (4-2-2-3) IPV4 Settings
6) - (4-2-2-3-1) Config Method (Auto = DHCP, Set to Manual in order to specify an IP address.)
7) - (4-2-2-3-2) Manual Settings (This is where you can set the IP Address, Subnet Mask, and Default Gateway.)

I don't know how to hook it up?

A PDF manual here---->LINK.

Pleas post and thumb back!

I am trying to set up a new printer to a Linksys router model no WRT300 Ver 2.0. I have lost my IP no and also my Network Security Key, Is there any way to retreive these nos Gordon Stephens

The router can be set to factory default by performing either of these two steps:

Resetting the Router Using the Reset Button
Resetting the Router Using the Web-Based Setup Page

NOTE: Pressing the Reset button on the back of the router for 30 seconds will reset your router to its factory default settings. All of the settings of the router will then be erased and the router's IP address will become

Accessing the Router's Web-Based Setup Page
NOTE:To access the router's web-based setup page using Mac, click here.
Step 1:
Open a web browser such as Internet Explorer.
Step 2:
Go to the Address bar and enter your router's IP address ("" is the default IP of most Linksys routers) then press [Enter].

NOTE : For WRP400, the default IP address would be "" and if you place the router behind a primary router with the IP address of "", then the router will automatically assume a new default IP address, "".

NOTE: If the IP address of the router has been changed, type the router's IP address in the Address bar instead.

The router's IP address can be changed by:

1. Running the router's setup CD.

2. Changing it on the router's web-based setup page.
If you forgot the router's IP address you can:

1. Check the router's IP address. For instructions, click here.

2. Press the Reset button at the back of the router for 30 seconds.

: This procedure will reset your router to factory defaults. Any settings on the router will be erased. The router's IP address will be "" and the password will be "admin".

Step 3:
A new window will prompt for a User name and Password. Leave the User name field blank then enter your router's password ("admin" is the default password), then click OK.

If you forgot the router's password you need to reset the router. For instructions, click here.


Which mobel router MC68EN360EM25C

I would be searching the Microsoft Knowledge Base for this answer. But 1st, I would look on the Motorola website for the answer.

NOTE: If the Router is physically connected to the Server (PC), via an Ethernet cable and you want to set it up, then


1. Check the manual for the IP No. of the Router (i,e., and then type into your Browsers navigation field (http://).


1. Search Motorola's website for the IP No. for the Router model :
1.1 Navigate to http://www.motorola.com
1.2 Select where you want to go, for Consumers OR for Business
1.3 Click Support.
1.4 Click the Get Product Manuals link, from the Business Support section.
1.5 Type the Product description into the Search field. Press <Go>.
1.6 Download the product Manual and open it.
1.7 Find the area in the Manual where it tells you the IP No. of the Modem (to access the Modems Settings).

2. Then type it into your Browsers navigation field (http://).

This connects you to the Setup / Installation menu of the Modem Router itself and enables you to configure it's settings. Generally, you are able to access help from within this area.

I hope this helps. Regards,

Eoc3220+ ip finder


reset your eoc 3220 and put the default ip address is bridge mode and ad mode ip is and put your pc ip,12,14,16 and open the web page and browse the or put user name and password ok!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Network between two remote location within City limits

well...first problem is you're going to have big network problems with both sites on the same network/subnet. Based on what you typed above, you will not be able to route packets between the offices since the router won't know which way to go...they must be different networks/subnets...e.g. You have quite a question there...I think you need to have a consultant talk with you over the phone at the minimum. If you can't find one locally you're welcome to work with us. Good luck


Open Internet explorer and type the ip address of the router in the address bar and hit enter. (it should be The setup page for the router should open. Click "Advanced" then click "ISDN Configuration" then click "ISDN Parameters" You can enter the new SPID's the phone company gives you there. Good Luck, El Duderino
Not finding what you are looking for?


Ask a Question

Usually answered in minutes!

Top Ramp Networks Computers & Internet Experts


Level 3 Expert

85242 Answers

Brad Brown

Level 3 Expert

19185 Answers

Cindy Wells

Level 3 Expert

6677 Answers

Are you a Ramp Networks Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides