Question about Fisher and Paykel GWL11 Top Load Washer

1 Answer

WAS THERE A RECALL ON FISHER & PAYKEL GWL 11

WAS THERE A RECALL ON THE FISHER & PAYKEL GWL 11 WASHER ,, DUE TO PUMP CAUSING SHORTAGE AND DAMAGE TO CONTROL MODULAR

Posted by GEORGE GARFUNKLE on

Ad

1 Answer

keith jones

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Fisher and P... Master
  • 747 Answers

No not thst i know of but its always been a problem with them over tha last 20 years

Posted on Apr 21, 2018

Ad

5 Related Answers

Anonymous

  • 22 Answers

SOURCE: GWL-11 Fisher Paykel wont turn on and water on the floor

Look at my issue "eco smart won't drain, smells hot". Mine is top load.

If you see puddle on floor and eventually won't run at all and smell electric burn motor, it could be same issue I had.

Unplug washer. Tip washer back. If you see water dripping through the black motor area, you need to remove the black motor and the white plastic unit above it. Look for a white plastic clip that is attached to bottom of washing machine. Push that clip with your finger and twist the whole plastic unit/black motor. It all comes off in one piece.

Look on side of this unit and you will see 120V or 240V. Mine is GWL10US and is older model. Was told by repairman that new units use 120V. That is what you need to order. It comes as one piece and you just twist it back on. I had done most of this. Repairman came and 5 seconds cost me $65.

Posted on Oct 20, 2008

Ad

Anonymous

  • 144 Answers

SOURCE: fisher and paykel washer gwl 11 us

ok You have a blown Motor controller module. There could also be another fault that caused this to blow up. eg a faulty drain pump, lid lock or Diverter valve, inlet valve. you'd need to use a ohm meter to test all these. cheers

Posted on Mar 24, 2009

Anonymous

  • 1 Answer

SOURCE: fisher paykel codes

There is a code book inside the top of the washer where the electronics are.

Posted on Apr 06, 2009

seakish

  • 492 Answers

SOURCE: when the washer (fisher & paykel gwl 11) goes into

Try unplugging the washer to reboot the curciut board. Leave unplugged for 5 min. Then replug and select only one setting. Multiple setting selected in a short period on time will confuse the little brain in the board. Reboot to fix. Be patient!

Posted on Apr 30, 2009

Lollo Pop

  • 134 Answers

SOURCE: no power to fisher paykel washer. Replaced pump

PUMP IS ALSO A HEAT SINK FOR THE MOTOR CONTOLLER.

YOU MAY NEED A NEW BOARD

Posted on Jul 10, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Where is the pump on my Fisher&Pakel GWL 11 AND HOW CAN I GET IT OFF TO CLEAN IT

Tilt your machine back on a 45deg, look up under machine to find pump
pull back on the white lever & turn anti clockwise to remove.
2_11_2013_6_44_03_am.jpg
0helpful
1answer

Replace fisher paykel iwl 16 mother board with gwl 11 motherboard

I cannot find your mothers IWL16 model, but I have found various similar machines that are the same phase as your GWL11 machine, the electronics in there although different are compatible, you can swap the drain pumps, there almost universal, avoid the drive shaft machine, fix the other one If you want further help, post a photo of both pcb's (the electronics) After swapping your machine will stil require programming which is simple enough
2helpful
1answer

Fisher and Paykel GWL11 Top Load Washer won't drain

Could be something in the pump. The pump is on the bottom of the tub.
It has a locking tab which you release and then twist the pump a hair and it will fall out. Warning: Have rags ready! I have the original GWL service manual and the GWL 11 supplimental manual. Let me know if you want them.


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

2helpful
1answer

During the rinse cycle, our GWL 11 Fisher & Paykel

The problem is in the pump, so it will not pump out, you will need to find another way to empty it, removing the agitator will make the job easier.
When you get the water out the pump can be accessed from underneath, it turns anticlockwise to remove it,.
I would buy a new pump as it is most likely that is all that is wrong with it.
3helpful
2answers

Fisher Paykal GWL-11 won't advance through cycles. Could this be

maybe blocked drain pump can u hear a buzzing when it tries to drain water
0helpful
1answer

Fisher paykel codes

There is a code book inside the top of the washer where the electronics are.
0helpful
1answer

Fisher and paykel washer gwl 11 us

ok You have a blown Motor controller module. There could also be another fault that caused this to blow up. eg a faulty drain pump, lid lock or Diverter valve, inlet valve. you'd need to use a ohm meter to test all these. cheers
1helpful
1answer

Balance Issues

Depending on the model you have the gwl 10 and 11 have a bal sw located under the console the sw may be engaging causing your problem. ( maybe corroded or shorted ) Or in later and current models they also have bal/shock struts on each side, one of the four maybe worn causing your unit to go out of bal.
Not finding what you are looking for?
Fisher and Paykel GWL11 Top Load Washer Logo

Related Topics:

295 views

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Ekse

Level 3 Expert

13435 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...