Question about JVC AV-56WP30 56" Rear Projection Television

11 Answers

SERVICE MODE IS THERE A SERVICE MODE FOR THIS TV THAT I CAN ACTIVATE TO TRY AND LINE UP MY BLUE CONVERGENCE PROBLEM

Posted by on

  • LMoore Nov 02, 2007

    Picture looks like double vision like the words are double and blurry I was told to use the remote to line up convergence but dont have remote anymore if this is what i need where do i get a replacement one?

  • brian Jan 20, 2008

    i have a hitachi 53fdx01b. something with my blue is off . the blue light doesnt go all the way up the screen but it not a staight line . it goes up about left 4 inches from top, middle 8 inches from top, right 2 inches from top. can you help.

×

Ad

11 Answers

  • Level 1:

    An expert who has achieved level 1.
    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a tv bluesky model PR14 .can anyone help me with service mode-

Posted on May 21, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,694 Answers

Always consult service literature for convergence and/or geometry procedures unless your experience is accurately memorized through frequent use. Ex.==SONY== press mute,then ENTER to write changes in memory.

Posted on Sep 29, 2007

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,694 Answers

Service literature will tell you how to adjust geometry and convergence in servicer mode.Just having the entry code is not enough info to complete alignment to near 100%.Senior tech skill level needed.

Posted on Sep 29, 2007

  • Level 1:

    An expert who has achieved level 1.
    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Depending on the age of your TV, there may be some manual adjustments as well. You can usually find these adjustments behind a piece of trim that is between your screen and speaker house on the front side. But as I mentioned... this is only on older units as the newer units have internal convergence PCBs that do it all through your remote control as mention by Hardrocko.

Posted on Aug 28, 2007

  • Level 1:

    An expert who has achieved level 1.
    Corporal:

    An expert that has over 10 points.
    Mayor:

    An expert whose answer got voted for 2 times.
    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

I had a problem with my TV colors not lining up. One day I turned it on and the green was out of wack. I checked this message board and replaced the STK chips, bad soldering and all led to me just giving up on that and buying a whole new Convergence Board ($185). I replaced the missing silver box on the new board and I just plugged this in and though now my Green lines up okay, my red is out of whack. Is there something I am doing wrong? Can anyone help me? Did i miss a step? Frustrated......Bruce

Posted on Aug 18, 2007

I have

Posted on May 21, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Also try http://www.bus.ucf.edu/cwhite/theater/ServiceMode.htm

Posted on Jan 13, 2007

I have a Sony KP-51WS500. To pull up the adjustment mode, turn off you tv then on the remote press Display,"5" button, "+" on the volume, and the power with in a second. Your TV should come on with GReen letters. After that press 1 and 4, 2 and 5 to change menus. Go to PJE (or something like that) and you should see PJE GREEN CENT, SKEW, SIZE etc. Press 3 to change colors, 6 to bring up the cross hatch and 9 to bring up fine tunning. Line each color up with the white boxes with the menu nipple thing. Press mute to write your changes then switch the TV on and off. Good luck.

Posted on Dec 29, 2006

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,694 Answers

A single-color mis-convergence problem is not the DCU.
The blue convergence amplifier IC is at fault---let me know if you
are still interested in repair procedure specific to your make and model-----I can detail step by step,just let me know.....T.

Posted on Oct 27, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

With tv off press and hold vol - and chan- u haft to press the vol first and hold both for 10 sec. use the buttons on the fron of the tv

Posted on Nov 11, 2007

Kim Yearick
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    Superstar:

    An expert that got 20 achievements.
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,476 Answers

Go to menu. Select either video or setup. Select convergence. There could be one or two setups. Try the automatic setup first. If it's just a minor problem this should work. Let it do it's thing and if all goes ok you should have a good picture. If this does not solve the problem do any other convergence setups available. If this does not solve the problem you probably have a bad digital convergence box. Less than $100 part but you'll need a tech to fix it.

Posted on Jun 22, 2006

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

6ya.com

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Convergence issue; red 3D effect. In grid convergence mode blue will converge w/green fixed lines and red horizontal will but the verticle red will not adjust far enough left to converge. has ajustment...
Convergence is dead.Must know how to solders?Must replaced ICS and all of it resistors.Tries Tv repair World.com,Tvrepairkits.com for a convergence kit.The shop will cost u $300 for parts and labors.

Jan 24, 2010 | Hitachi 43FDX01B TV

1 Answer

Can not get the red & blue lines to align for boxes 3,7,9 on the Convergence mode For Toshiba 61H70 Projection TV. The blue and red lines will move but will not reach the distorded green line. Any...
Ur convergence it dead,Must know how to solders?Buy a convergence kit,replaced what in that kit.Tries Tv Repair World.com,Tvrepairkits.com.

Dec 23, 2009 | Toshiba 61H71 61" Rear Projection...

2 Answers

Toshiba 57H82 convergence problems. TouchFocus
See my solution <http://www.fixya.com/support/t2795690-convergence_off_blue_line_only_vertical>.
You need to get to the service menu--it's been 4 years so go to AVSforum.com to turn off the different guns and get the better pattern.
At your risk: To get into Service mode:
1. Turn your TV on. 2. For X81 or earlier series: Press MUTE on your remote and release. 2. For H80/H81/HX81 series: Press MUTE on your remote and release two times ("Mute" on-screen) 3. Press down MUTE on your remote again and hold. While holding, press the MENU button on your TV set's front panel. 4. Release both buttons. 5. An "S" should appear on your screen. Press MENU again on your TV. 6. Now you're in service mode. Channel Up/Dn - Scrolls through Parameters and Volume Up/Dn - Changes Parameter Value
To get into convergence mode:
Get into Service mode, then Hit '7' to bring up the convergence grid. Buttons 100, 0, and ENT control which gun you want to turn off (if you want to align the red to the green without seeing the blue gun and other variations). 2=up, 8=down, 4=left, 6=right, 3=change gun to converge, 5=converge that point. To exit convergence mode you press 7 once and your screen should look like it's imploding then return to normal and then you press 7 to get back into regular service mode.
I have more info found on the board. -Ken

Jul 31, 2009 | Toshiba 57H82 57" Rear Projection...

2 Answers

43 philips problem with green
Your TV most likely has one or more possible problems.

Problem #1: Convergence Chip Failure ( common problem )

Here are some of the most common symptoms and example photos of a convergence problem
  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
701cb04.jpg
77ea520.jpg
f0900cb.jpg
Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.



You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.

2c07611.pngSolution #1

You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick note and they will put one together for you. Their kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, etc.


Problem #2 CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.

578ba6c.jpg
TV set after fluid change

65af323.jpg

2c07611.pngSolution #2


What you will need to do is replace the coolant and clean the crt. You can get a repair kit from www.TvRepairKits.com that includes replacement coolant, photos. instructions, etc.

Jan 24, 2009 | Philips 43PP9202 43" Rear Projection...

1 Answer

PICTURE HAS DISTORTED HORIZONTAL LINE IN CENTER OF SCREEN.
Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony, Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit from the link below.

Common Symptoms include....
  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on - TV may also make a chirping noise.
Here are some photos of convergence problems.

49abec3.jpg
f0add3d.jpg


Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a solution

93a1209.pngCONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you know what you are doing. If you have never done this before we would advise calling a shop or if you want to do it yourself get a complete kit with instructions and support from www.TvRepairKits.com

Jan 03, 2009 | Toshiba 55H70 55" Rear Projection...

3 Answers

Convergence will not line up after replacing ic & resistors
Did you replace the resistors when you replaced the convgence chips? If one of them was bad you would still have the problem.

Here are some of the most common symptoms and example photos.

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
701cb04.jpg
77ea520.jpg
f0900cb.jpg

Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.



You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.


2c07611.pngSolution


You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick email and they will put one together for you. Their kits includes photo instruction guides, original Sanyo STK chips, convergence resistors, pico fuses, etc.

Jan 03, 2009 | Philips 51PW9303 51" Rear Projection...

1 Answer

Setting convergence using service mode on the tv.
Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projeciton sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some photos of convergence problems.

42d3683.jpg

7859b01.jpg

e87380c.jpg
Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

69189a5.pngCONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you are handy and can follow directions. You can get complete repair kits from TvRepairKits.com or click here. They have put together DIY repair kits that include the OEM parts and step by step photo instructions for each repair. If you are not handy or can't follow directions we would suggest calling a shop.

Nov 23, 2008 | RCA P46920BL 46" Rear Projection...

1 Answer

43F300 convergence
Convergence kit # X480306 for your Model #.....
Replace parts & activate auto-focus......T.

Sep 01, 2008 | Hitachi 43F300 43" Rear Projection...

1 Answer

"Perfect Focus" problem on Samsung HCN4727W
You have a bad sensor, a bad digital convergence board, or the new board is not working correctly. I would start by swaping out the convergence board or exchange it for another one. Good Luck

Nov 08, 2007 | Televison & Video

1 Answer

Loss of convergence after powering off.
you must enter the service mode and align your convergence and save it to the epromm also activate the auto focus to activate the sensors , power on /mute-1-8-2- / press enter to save and before you exit activate the focus key on the remote ,very inportant to do the last step./g

Apr 29, 2007 | Samsung PCN5425R 54" Rear Projection...

Not finding what you are looking for?

View Most Popular

AV-56WP30 56" Rear Projection Television

  • Televison & Video

Related Question

Convergence issue; red 3D effect. In grid convergence mode blue will converge w/green fixed lines and red horizontal will but the verticle red will not adjust far enough left to converge. has ajustment...

  • Hitachi 43FDX01B TV

Open Questions:

0 Answers

why is the blue powerlight is the only thing that is working on a jvc av-56wp30

Jun 25, 2014 | JVC AV-56WP30 56" Rear Projection...

0 Answers

av56wp30 TV went blank and the power light continues to blink on and off The TV screen went blank and the power light on the front TV blinks on and off. What is causing this problem and how can I fix it?

Jun 17, 2014 | JVC AV-56WP30 56" Rear Projection...

0 Answers

cooling fan for lamp is not working

Mar 15, 2014 | JVC AV-56WP30 56" Rear Projection...

0 Answers

How do I reset channels from the Menu on the tv

Feb 01, 2014 | JVC AV-56WP30 56" Rear Projection...

See all JVC AV-56WP30 56" Rear Projection Television Questions

Related Topics

JVC AV-56WP30 56" Rear Projection Television Logo

2,013 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

JVC AV-56WP74 56" Rear...

JVC XV-N320 DVD Player

JVC AV-32260 32" TV

JVC RM-C18G-1H Remote Control

JVC HD-52Z575 52" Rear...

Check Out the Latest HD Televisions Report
Check Out the Latest HD Televisions Report

View all Fixya Reports

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76171 Answers

Todd Hill
Todd Hill

Level 2 Expert

433 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. AV-56WP30 56" Rear Projection...

AV-56WP30 56" Rear...

Loading...