Black comes across right side of screen

A black thing comes from the right side and moves over to the left, leaving about a quarter of screen. sometimes there is a squealing sound and then the left and right sides go and in the middle is a distorted picture. we use to jiggle the cable at the back and sometimes it would just disappear and the picture would be fine. the sound is fine.

alex07 Apr 16, 2008

hi! i have a problem with my t.v.when i turn it on,,a thin curv vertical line in the left side appear on screen! sometimes,,it will move going to the middle and after a few minutes,,it will shut off! the sound is ok! plss help me,,thanks a lot!

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.
Master
3,130 Answers

Sounds like you've got whats called a cold solder connection somewhere in the horizontal width control circuit or a connection in the sweep section. Should'nt be two expensive but unless you have had some soldering and troubleshooting experience I would leave this on to the pros. Good Luck

Posted on Jun 02, 2006

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

Very thin black vertical line moving across tv screen left to right on tv

The screen voltage to the picture tube is more than normal. Adjust it by the help of screen pot-meter integrated with Line Output Transformer. Visit the site named 'Electro-help' for more details. Check this link and select the site named above. View it in 'Flip card' option, which can be selected from the drop down box menu at the left top corner or the display window. It will make search easy.

Read full answer

Aug 05, 2012 • Panasonic CT-20SL14 20" TV

0helpful

1answer

After several years of good printing performance when connected to my XP Dell PC, and later moved to my Vista PC, my HP PSC 1610 printer began 'acting up'. The first problem was it would begin printing...

Have you tried to reinstall the printer software with the Vista version? Go to www.HP.com and download it. See if that will solve your problem.

Read full answer

Jan 14, 2011 • HP PSC 1610v All-in-One Printer

0helpful

1answer

Screen is off tilt a little. Right side is about a quarter inch higher on the screen than the left. You can only tell when there are menu bars or scoreboards that go all the way across the screen. I think...

you really need a trained tech with a service manual to adjust.

Read full answer

Oct 28, 2009 • Samsung HLR5064W DLP Projection TV

0helpful

1answer

Picture not centered on my philips 47'' lcd tv

NOTE:(Edited and copied from another thread on Fixya.com, c7carl)

Picture is not centered on monitor leaving a 2 1/2 inch; black border on Philips LCD
By dmorrow54 on Nov 13, 2007
Again, nothing in manual for Philips LCD will correct the fact that the picture in HD-D mode will not center. The picture runs off the monitor on the left (facing the monitor) with a 2 1/2" black border on the right (facing the monitor). Using the format button on the remote of directional arrows will not correct the issue. The wide-screen/ full-screen function with format does nothing. Moving into TV mode, the format function works to display screen in several ways 4:3, 19:2, super-zoom, wide-screen, full-screen. Help, please. posted 3 years ago

Guest

Rank: Guide
Rating: 0%, 0 Votes

I have a Philips 30 inch LCD and solved the problem by using the circular arrow button on the TV remote. Pointing it at the TV and clicking "right" (3 o'clock on the button), the picture moved right. Same thing on for "left". Worked for me.
Add a comment

- c7carl
- 5 minutes ago
WOW! It works!! The picture on my Magnavox (aka Philips) 37MF321D had shifted to the right. I figured I had a big repair bill coming up soon. But hey! Just used the TV remote as described by "Guest', and re-centered the picture to the left. Wallah! Thanks ""Guest" whomever you are! Reply

Posting advertisements, profanity, or personal attacks is prohibited. Click here to review our Terms of Use.
Comment:

Read full answer

Feb 05, 2009 • Philips 47PFL5603D 47 in. LCD HDTV

0helpful

1answer

Yellow area on screen

either burn in or magnetic field interference. I suggest moving any speakers away from the tv. if thats not the case, then find a strong magnet, make sweeping motions across the screen with it but dont touch the screen! Keep doing this until the colors change, then "sweep" them with the magnet into a corner and they will mostly dissapea.......r, sounds complicated but worked for me. can be scary so dont try unless sickly despearate or confident. Hope This helps!

Read full answer

Jan 24, 2009 • Panasonic PT-51HX42 51" Rear Projection...

0helpful

2answers

Very faint vertical bar moving across plasma screen.

OK... Left to Right is weird. I'd say one of two things.
Refresh Rate might be to low or to high, but i doubt this to be the cause. I'll put my money on external interferences. Something like another PC screen? TV? anything magnetic and I've even in some cases noticed PC side panels too close to a screen can cause this.

Read full answer

Dec 29, 2008 • Computers & Internet

0helpful

1answer

Philips TV Model 32DW6557/05 Screen Problem

hi it sounds like a capacitor in the verticle circuit located on the main board. it is near the verticle ic. the verticle ic also could be bad the cost is around 85 dollars for a tv shop to fix. sometime a cold joint could be found around vert ic. a soldering iron is required with solder.tap the side of tv if picture comes back it is just cold solder joint.

thanks Doctor video

Read full answer

Apr 25, 2008 • Televison & Video

11helpful

2answers

MacBook opening screen leaves a one inch black strip on both sides.

use the gray bar on top to move the screen to the upper left hand corner. Then click and drag the bottom right portion of the screen to the size that you want it be.

Read full answer

Mar 21, 2008 • Apple MacBook PC Notebook

0helpful

1answer

Screen adjust changes when entering/leaving full screen games

When your not playing games does it have this problem? You should update the drivers for the monitor and your video card and even the games for that matter, all of those have updates. Update all of these items and see if the problem still exists. You may try running a virus/spyware/other boogies scan too you never know what ilk they may spread. We'll keep the warranty thing in mind but try the above updates. http://www.viewsonic.com/support/drivers/drivers.cfm?category=1&formName=monitor let me know what happens. Tim

Read full answer

Mar 21, 2007 • ViewSonic VA712B 17" Flat Panel LCD...

0helpful

1answer

Screen Adjustment

On your monitor at the bottom there is 3 buttons. The one all the way to the left is the "menu" button. The next one (going right) is the "NEGATIVE" button. The next one (going right) is the "POSITIVE" button.

You can move your screen around. First, start by pressing the menu button.Then, a menu in blue, with a bunch of little white icons will appear. Next, go over two icons by pressing the positive button twice. Then, proceed to push in the "menu" button again. A bar will appear. By pressing your negative button, your screen will move left. Pressing your positive button will make your screen move right. Adjust your screen until the black on both sides are of even proportion. Then, press the menu button to return to the orginal menu you started at. Proceed to press your positive button two more times. Then, press your menu button. Then, once again, use your positive button, and your negative button to adjust your screen to even out the black on the top and bottom.

Read full answer

Dec 24, 2006 • HP Compaq FS 7550 17" CRT Monitor

Not finding what you are looking for?

View Most Popular

AV-36D502 36" TV

Televison & Video

Very thin black vertical line moving across tv screen left to right on tv

Panasonic CT-20SL14 20" TV

Open Questions:

0answers

no power jvc av-29st17

Read full answer

Be the first to answer Mar 18, 2013 • JVC AV-36D502 36" TV

0answers

JVC AV-36D502 belonging to my 99 year-old father somehow got set to close captions (i managed delete the closed captions) and SAP. i cannot get the SAP setting changed to STEREO. using the menu i can get STEREO highlighted, but the TV is still in SAP mode. i don't understand exactly how things are selected in the menu--the manual says toggle up and toggle sideways, but says nothing about how to lock in changes. best i can do is make changes and quit the menu, but the SAP selection is unchanged after i have done that. thanks. keith

Read full answer

Be the first to answer Mar 22, 2011 • JVC AV-36D502 36" TV

109 views

Ask a Question

Usually answered in minutes!

Check Out the Latest HD Televisions Report

View all Fixya Reports

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual

. AV-36D502 36" TV Manual

AV-36D502 36" TV

Have a manual for JVC AV-36D502 36" TV? Or just drag it here!

Related Topics:

Black comes across right side of screen