What is the pin code for this holden stereo F-TEN CDT5590. I disconnected the battery to clear airflow meter fault. Now stereo wants a code entered in to enable it.

The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

Hi Did you by any chance have ignition swithed on when you refitted new battery? If so disconnect negative terminal at battery for about 5 minutes all modules will go to sleep and reset (ign off) reconnect battery and try again. If that does not work you will need a fault code reader. It is advisable to connect a fault code reader 1st however as you have already disconnected the battery it has probabley lost any fault codes anyway,Good luck

Clearing the codes is simple that is done by removing the fuse of the EFI from junction box 2 for 10 seconds. Make sure to remove the jumper wire and switch the key off before clearing the codes.

Here are some common Lexus vehicles 1990-1995 codes:

Code 12 and Code 13 Rpm signal circuit fault
Code 14 Igniter signal circuit fault
Code 16 ECT control signal fault
Code 21 and Code 28 Main oxygen sensor fault (for ES300; SC300 & GS300 models)
Code 22 Coolant temperature circuit fault
Code 24 Intake temperature sensor circuit fault
Code 25 and Code 26 Air fuel ratio fault (for ES300 & SC300 models)
Code 27 Sub-oxygen sensor circuit fault (for ES300 CA & GS300 models)
Code 31 Low airflow meter voltage (for ES300 and GS300 models)
Code 32 High airflow meter voltage (for ES300 model)
Code 35 Barometric pressure sensor circuit fault (for GS300 & SC300 models)
Code 41 and Code 47 Throttle position sensor circuit fault
Code 42 Vehicle speed sensor circuit fault
Code 43 Starter signal
Code 51 Switch condition signal fault (for ES300; GS300 & SC300 models)
Code 52 Code 52 and Code 55 Knock sensor circuit fault
Code 71 EGR system circuit fault (for ES300; GS300 & SC300 models)
Code 78 Fuel pump control circuit fault (for GS300 & SC300 models)

When you disconnect your battery and then reconnect it again, it disables the radio. This is an anti-theft protection for your car radio.
The enable your radio the activation code is in your vehicle owner's manual. If you do not have this code you need to go to your Holden service centre and get them to enter this code for you.

Connect the battery and then enter the unlock code.

Yes need code for Holden rodeo

When you disconnect the battery from the car, the stereo needs a pin code to activate the stereo. This is an anti-theft measure.
This code is in the vehicle's manual, if you do not have this manual, you will need to take your vehicle to your GMH Holden's service center to get this code.

My ford dose the same thing you will need the original car booklett in it sould be a little white card which has the code on it! if you have not got the card/book go in to a holden shop or ring up Holden motors

WRONG! Leave the radio on for 1 hour using the key and accessories to reset then enter the pin. You get the pin from nissan customer service in your area but you need to supply your vin/chassis number.

To enter the pin you press buttons 1-4 corresponding to the number of the pin eg. pin is 1023, press button 1 once, 2 ten times, 3 two times, 4 three times

pin is on the metal frame of radio on left or right side and on sticker starting with the letters BP- then your 4 dig pin also the radio code after the pin write it down to. swich your radio off press hold the AS button while holding AS button down press power button it will automaticaly ask for security code enter security code then radio code