Question about HEWLETT-PACKARD HEWLETT PACKARD HP COLOR LASERJET CP2025DN Duplex Unit

2 Answers

HP Color LaserJet CP 2025dn error code 59.70

I just installed a new cyan toner cartridge and after initializing I am getting in the printer display "59.70 Error Turn off then on" which I have done now 3 times, but the same error code comes back. Any advice would be appreciated.

Posted by Clark Kent on

Ad

2 Answers

OSU_Matthew

  • Level 1:

    An expert who has achieved level 1.
    Governor:

    An expert whose answer got voted for 20 times.
    New Friend:

    An expert that has 1 follower.
    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 4 Answers

We had a persistant Error 59.70 with an HP m452DN printer, which kept up after power cycling the device. Since it's an error with the black toner developer motor, I pulled the black toner, powered up the printer, and manually checked the drum on the toner for seizure. Rotated the drum by the knob on the side to free it up, and then reinserted and printed a cleaning page. Printer works fine now.

Posted on Oct 26, 2016

Ad
Wayne Buchanan

Wayne Buchanan

  • Level 1:

    An expert who has achieved level 1.
    New Friend:

    An expert that has 1 follower.
    Welcome Back:

    Visited the website for 2 consecutive days.
    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

59.XX this error is related to the fuser possibly a bad cartridge I have seen cartridges with the rollers seized & can't turn which will create different error codes

Posted on Apr 18, 2014

Ad

1 Related Answer

let me help

sheraz Gul Bar

  • 196 Answers

SOURCE: I have a networked hp 2025dn printer the problem

my personal opinion is that you might have two basicproblems

1.open the lid from back of your printer, you may see a stiff film .,give aprint command and check the film rolling visually , if its broken then it mightgive you annoying sound like something's broken , but it can only be visualizedgiving a print command ,
if its really broken from edges it may give you this problem, it can be fixedby local service center ,I had this problem it cost me about 2.(clean your printer ) >Open printer >remove the toner > check for any piece of stapler pins or any paper or anyother waste that's stuck in between drums. > if you have a wind blower machine blower it . > must keep in mind to blower it in open area, causeblack particalls will make you cough, or would get dusty, 3. your toner must have ink dust at one side, shake thetoner and then insert in printer , this will help you . I hope it helps you

Posted on Mar 29, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code e1 showing at xerox pro 420? solution..
rror codes If the printer's front panel displays a message Error XX, find the error code in this table and follow the instructions for resolving the problem. If problems persist, check the Xerox web site www2.tek.com/TekSMART/ or contact service.
Error User Corrective Action Error 01
  • Remove and re-install the black Toner Cartridge, then turn the printer off and on.
  • Replace the black Toner Cartridge, then turn the printer off and on.
Error 02
  • Remove and re-install the cyan Toner Cartridge, then turn the printer off and on.
  • Replace the cyan Toner Cartridge, then turn the printer off and on.
Error 03
  • Remove and re-install the magenta Toner Cartridge, then turn the printer off and on.
  • Replace the magenta Toner Cartridge, then turn the printer off and on.
Error 04
  • Remove and re-install the yellow Toner Cartridge, then turn the printer off and on.
  • Replace the yellow Toner Cartridge, then turn the printer off and on.
Error 05, 10, 11,12, and 13
  • Turn the printer power off, then on.
Error 20
  • Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • Remove and re-install the Main Charge Grid. Turn the printer off, then on.
  • Remove and re-install the Transfer Kit. Turn the printer off, then on.
  • Remove and re-install each of the Toner Cartridges. Turn the printer off, then on.
  • Replace the Main Charge Grid. Turn the printer off, then on.
  • Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • Replace the Transfer Kit. Turn the printer off, then on.
  • Replace the Toner Cartridges. Turn the printer off, then on.
Error 21, 22, 30,and 32
  • Remove and re-install the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • Replace the Imaging Unit (make sure that Imaging Unit is locked in place). Turn the printer off, then on.
  • If a problem persists for Error 30, clean the sensor. See Cleaning Phaser 750 Printers.
Error 33
  • Check for jammed paper throughout the paper path (especially in paper feeder).
  • Remove and re-install the paper feeder and Transfer Kit. Turn the printer off, then on.
Error 40, 41, 42,and 43
  • Check for jammed paper in the Fuser. Re-install the Fuser. Turn the printer off, then on.
  • Make sure that you have the correct Fuser for your local printer power supply:
    110-Volt Fuser Part Number 016-1839-00
    220-Volt Fuser Part Number 016-1840-00
  • Replace the Fuser. Turn the printer off, then on.
Error 50, 51
  • Turn the printer off, then on.
Error 52
  • Remove the Duplex Unit (if installed).
  • Check for paper under the Upper Tray.
  • Turn power off, then on.
Error 53
  • Open left door and remove any jammed media.
  • Tun the printer off, then on.
Error 60
  • Remove the media from the Multi-Purpose Tray. Turn the printer off, then on.
  • Reinstall the media. Make sure you do not overfill the tray.
Error 61
  • Remove and re-install each Toner Cartridge. Turn the printer off, then on.
  • Replace each Toner Cartridge. Turn the printer off, then on.
Error 62
  • Check for jammed paper throughout the paper path (especially in the paper feeder and Fuser).
  • Remove and re-install the Fuser. Turn the printer off, then on.
  • Slide out and re-insert the paper feeder. Turn the printer off, then on.
  • Replace the Fuser. Turn the printer off, then on.
Error 63
  • Remove and re-install the Imaging Unit. Turn the printer off, then on.
  • Replace the Imaging Unit. Turn the printer off, then on.
Error 70, 71, and72
  • Turn the printer off, then on.
Error 73
  • Remove and re-install the Imaging Unit. Turn the printer off, then on.
  • Replace the Imaging Unit. Turn the printer off, then on.
Error 74
  • Remove and re-install the Fuser. Turn the printer off, then on.
  • Replace the Fuser. Turn the printer off, then on.
Error 80, 81, 82,83, and 84
  • Make sure that all four toner cartridges are installed in the printer.
  • Turn the printer off, then on.
Error 01p through
Error 47p
  • Make sure that installed memory DIMM(s) are compatible with printer's image processor board and that they are installed in the proper slot(s).
  • you can helpful

Oct 09, 2014 | Xerox Phaser Office Equipment & Supplies

1 Answer

Error c cart
Try the following...
-Remove the cyan cartridge from your printer and close any open doors.
-Turn the printer off.
-Turn the printer on again.
-Firmly re-install the cyan toner cartridge.
This will force your printer to actively look for a new toner and hopefully it will be accepted this time. If the problem remains install the old toner cartridge (if available) to make sure the error disappears.

Assuming it does it would appear there may be a genuine fault with the toner cartridge. If not there is almost certainly a sensor error inside the printer and I would advise contacting Dell (if it is within warranty) or a technician if it is outside of warranty.

Sep 11, 2012 | Dell 3110cn Laser Printer

1 Answer

I replace the Cyan cartridge on my HP PhotoSmart C6180 printer. Now I get the error message on the printer screen "Incorrect Ink Cartridge". I noticed the old cartridge has the part number...
That is the problem, I suggest you return it and something they will replace it for free. Make sure you get the correct toner part number is this cartridge is not compatible with your printer. Regards

Jun 23, 2011 | HP Photosmart C6180 All-In-One InkJet...

1 Answer

Ricoh CL4000DN. I recharged the magenta toner using the OEM cartridge. I replaced the chip as instructed and all elements snapped together without difficulty. However, now there is a "check toner...
Hi, the chip on those toner bottles stores information about how much toner is left, so once that chip registers an empty toner bottle, it won't work even if you attach it to a new toner bottle. You'll need the chip from a new toner bottle, or one that hasn't registered no toner.

Jan 22, 2011 | Ricoh CL4000DN Laser Printer

1 Answer

HP Laserjet 5550dtn printer is giving error 59.51, what will be the problem?
This code means there is a Cyan Cartridge motor error. The most common cause of this error is the Cyan Toner/Drum cartridge is binding up and causing the motor to stop turning. I would try removing then re-installing the Cyan cartridge first and see if it goes away. If not then replace the Cyan cartridge with a new cartridge. If the problem persists then there is a problem with the drive assembly for the Cyan cartridge.
Good Luck and Thank You for using Fixya.

Sep 03, 2010 | HP LaserJet 5550dtn Printer

1 Answer

Toner sensor error
Hi


This error comes up when the printer detects that the toner of particular color is missing. This indicated that the indicated color toner is missing from the printer(eg-- C = Cyan, Y = Yellow, M = Magenta, K = Black).

C5150 may face a toner sensor error after installing used sets of toner cartridges and sometimes even after installing new toner cartridges as well. This error can be bypassed. This can be disabled by following these steps---

1. Turn machine on while pushing and holding the (+/-), menu buttons at same time.
2. Menu window will show OKI USER.
3. Scroll to Engine Dialog Mode is indicated Push Enter button.
4. Diagnostic Mode xx xx xx S Mode is indicated.
5. ( = 2 ) . Press (- or +) button until “ENGINE - PARAMETER SET =2” is displayed.
6. Push Enter button.
7. TONER SENSOR - ENABLE is displayed.
8. Push Enter button.
9. Press (- / +) TONER SENSOR = DISABLE is displayed.
10. Press ON LINE CANCEL buttons at same time.
11. (*) is displayed.
12. Restart the Printer.

Daniel Scott

Jun 22, 2010 | OKI C5150n Led Printer

1 Answer

Install cyan error
Error 02. Remove and re-install cyan Toner Cartridge, then turn the printer off and on. Replace cyan Toner Cartridge, then turn the printer off and on. ...
www.office.xerox.com/userdoc/P740/P740man/740.33.html

Dec 04, 2009 | Brother Multi-Function Center MFC-3360c...

1 Answer

After removing toner cartridges error display said replace various colour toners.
it is not according to your printer or your head of cartige is not clean or damage. try replace new one

May 09, 2009 | Xerox Phaser 6100/BD Laser Printer

1 Answer

Epson Aculaser C1100 erro message install C tnrcart
You need to remove the cyan cartridge, and thoroughly clean the inside of the printer (please use proper printer cleaning kit, not a damp cloth!). The sensors can get crudded up with loose toner inside the machine.


Oct 28, 2008 | Epson Aculaser C1100 Printer

1 Answer

Install Cyan Toner Error
ensure that the one you install is the exact model name and number, if this is correct, try unistallling once again and check one more time,

you might want to get a new cyan toner if this still fails, i dont think there is a prob in your machine, cheers

Aug 16, 2008 | Samsung CLP-510 Laser Printer

Not finding what you are looking for?

View Most Popular

HEWLETT PACKARD HP COLOR LASERJET CP2025DN Duplex Unit

  • Office Equipment & Supplies

Related Question

Error code e1 showing at xerox pro 420? solution..

  • Xerox Phaser Office Equipment & Supplies

Open Questions:

0 Answers

hp laser jet pro error 59.70

Jan 29, 2014 | HEWLETT-PACKARD HEWLETT PACKARD HP COLOR...

0 Answers

I get a "printerror" after every 2 or 3 sides of I get a "printerror" after every 2 or 3 sides of print, if I hit ok then it prints but goes straight to a cleaning and calibrating function. What could be causing the error?

Jun 09, 2011 | HEWLETT-PACKARD HEWLETT PACKARD HP COLOR...

Related Topics

HEWLETT-PACKARD HEWLETT PACKARD HP COLOR LASERJET CP2025DN Duplex Unit Logo

7,792 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

1 Answer
How to self test page of HP laserjet P1102?

HEWLETT-PACKARD Hewlett Packard...

1 Answer
HP LASERJET P1606DN goes to offline

HEWLETT-PACKARD LASERJET PRO...

1 Answer
Reset hp t790

HEWLETT-PACKARD T790 InkJet...

1 Answer
How to solve error 79.2:04 at T2300eMF

HEWLETT-PACKARD T2300 eMFP...

2 Answers
Where can I download User Manual(s) for hewlett

HEWLETT-PACKARD 48SX Calculator

Check Out the Latest Printers Report
Check Out the Latest Printers Report

View all Fixya Reports

Top HEWLETT-PACKARD Office Equipment & Supplies Experts

Harrie

Level 3 Expert

6740 Answers

Duke Bells

Level 2 Expert

131 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Are you a HEWLETT-PACKARD Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...