Connecting to computer

CD370 errors occurs when• Multiple errors are detected by the
abnormal check of each NVRAM data.
You need to reset the printer's NVRAM . First find out how.

It isn't mentioned in the KBizhub350 User Manual, as required by government. Any fraudulent activity is also kept on the nvram. (copy bank notes).

It is possible that you camera having trouble to the card port. If you are familiar disassembled camera you need to use a circuit tester. Try to resoldered the card port on your camera just to insure the connectivity working.

Just ask near electronic shop to resoldered the card port if you are afraid to avoid damage to your camera. Sometimes this because of a capacitor could no longer supply value of voltage inorder to detect the card.

I don't beleived that this was not affected with a viruses because as what you stated you can used the card through card reader with computer. So that mean's the internal problem is from your camera.

Please let me know any update.

DID you swap a board from a different machine if so you really messed up the machine, Have a tech come out to look it over mite run below? NVRAM holds the serial number and counts so people cant erase the counts as new.
CD3##: NVRAM Data error
• When the data stored due to the NVRAM trouble is lost, backup data can be used for restoration.
• Trouble code [C-D370] will be displayed when multiple errors (over 5) of NVRAM data are detected, which can be restored with one restoration command.
• Data backup will be automatically performed every hour. Backup can also be performed manually with the following setting.
[Service Mode] ? [Enhanced Security] ? [NVRAM Data Back Up]
Touch the following code on the trouble code display screen.
Stop ? 0 ? 7 ? 1 ? 3 ? 9
2. [*] will be displayed on the trouble code screen.
3. Touch [*].
4. The screen will be shifted to the data restoration screen to perform data restoration.
NOTE
• When the restoration is performed in a short time, data restoration screen may not
be displayed.
5. Check the message which indicates that the data restoration was successfully conducted.
Turn Main power OFF, and wait for ten seconds or more to turn it back ON.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

One Beep (Possible system board failure - BIOS ROM checksum failure)
Two Beep (No RAM detected)
Three Beep (Possible system board failure - Chipset error)
Four Beep (RAM read/write failure)
Five Beep (Real Time Clock failure)
Six Beep (Video card or chip failure)
Seven Beep (Processor failure)
Eight Beep (Display failure)

DELL BEEP CODES
Beep Codes Beep Code Description Failure Coverage 1 System Board: BIOS ROM failure System Board, covers BIOS corruption or ROM error 2 Memory No Memory / RAM detected 3 Chipset Error (North and South Bridge Chipset DMA/IMR/ Timer Error for Intel platform); Chipset Error System Board Chipset Failure Time-Of-Day Clock test failure. Gate A20 failure Super I/O chip failure Keyboard controller test failure. 4 RAM Read/Write failure Memory failure 5 RTC Power Fail. CMOS battery failure 6 Video BIOS Test Failure Video card / chip failure 7 CPU Cache Test Failure CPU failure 8 LCD LCD failure

this problem caused by error connection at hard disk, your hard disk can not read by your computer

to fix this problem you need to open your laptop then disconnect your hard disk from laptop, and connect again
and turn on your laptop

the problem like this usually found at computer with sata hard disk connection

i hope this helpful

use Apple Hardware Test to diagnose the error::
1 Disconnect all external devices from your computer except the power adapter.
If you have an Ethernet cable connected, disconnect it.
2 Insert the Mac OS X Install Disc 1 that came with your computer.
3 Restart your computer and hold down the Option key as it starts up. A list of available
startup volumes appears. Click Apple Hardware Test and click the right arrow.
4 When the Apple Hardware Test main screen appears after about 45 seconds, follow the
onscreen instructions.
5 If Apple Hardware Test detects a problem, it displays an error code. Make a note of the
error code before pursuing support options. If Apple Hardware Test does not detect a
hardware failure, the problem may be software related.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Where can I get the photo editor for the MM Digital Camera TT-MK07

Thank you for providing your configuration details.
You have failed to specify wheather or not your LCD Display is under Warrenty.

Perhaps these simple trouble shooting procedures will get the job done.

1. use the DVI to VGA adaptor that came with your card

Plug in a regular CRT monitor to the Primary Display Output Port using the DVI to VGA adaptor
( either port can be designated as the primary by you )
I like to use the Port nearest to the motherboard as the Primary

2. plug in the your LCD monitor on Secondary Display port using your DVI cable

At this point you should be able to see your desktop on the Primary CRT Display

3. Go to the display properties and use the Nvidia Dual Display Setup Wizard

set both desktops to CLONED at a resolution of 1024x768 and set the refresh to 60Hz
which is default for most LCD displays , some have higher refresh rates , consult your user manuel

If the display resolution and refresh are set incorrectly for your CRT or LCD you will see
Signal Out of Range ( if the display has the ability to display that error message )

At this stage both displays should be showing a Windows Desktop

If you now see your desktop on both displays , you can now put the LCD on the Primary Port



No Signal Detected ( this means the display device is not receiving a signal )

If your LCD display is still displaying the error message
"No Signal Detected" after performing the trouble shooting proceedures
You may need to read the user manuel about how to enable DVI signal input.

If you are certan you have done everything correctly but still see only "No Signal Detected"

Your LCD Display may need replacement

Loch Hime :-)

Hi,

C3451: Heat. Heater Trouble

You have to check machine fuser unit .
May be paper on the fuser unit. Check fuser unit rollers.

After check fuser unit you have to ececute a "trouble reset".

Turn on your machine by press and hold "utility counter" botton, after some seconds press to display "TROUBLE RESET" and turn off and on machine.


C4551: Cyan laser Malfunction

Check cyan laser connection and execute trouble reset.

Bye.