Question about NRS Mad Gab Mania DVD Game

1 Answer

How to put a mad gab timer back together

My brother unscrewed the timer and how do put the gears and such back together?

Posted by Anonymous on

Ad

1 Answer

Alexis Miller

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Help. Happened to us too! Anyone?

Posted on Oct 13, 2012

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i put my sewing machine back together


Ugh!!! Just look for a parts diagram. That should help you figure out where pieces go.

Search for:
Make Model parts diagram

Dec 27, 2017 | Brother Sewing Machines

1 Answer

Hoover steam carpet cleaner - turbine needed for F7458-900


Once you get the turbine out, open it up by unlatching the three latches and unscrewing two screws. Pull the gears out and WD40 everything. Let it sit for a bit and start turning the solver gear at the back with a pair of pliers. Once it is loose, put all the gears back together and return everything to it's place. FIXED! without buying a new turbine....

May 30, 2012 | Hoover Steam Vac Dual V w/ SpinScrub...

1 Answer

Whirlpool Ultimate Care II gas dryer won't turn off.


Dryer Won't Stop Running
  • Ultimate Car II Dryers are fitted with a mechanical timer that sends an impulse to the control circuit board to stop running once the set amount of drying time has elapsed. This is because, should an electronic timer fail, this would necessitate the replacement of the entire circuit board. Confirm that the mechanical timer is indeed broken by opening the dryer's door. If the dryer stops, the circuit board is working fine and is not the problem. Simply slide off the protective faceplate of the dryer, unscrew the control board beneath, and flip it over. Connected to the back of the timer's knob should be a small round device with two wires running to the circuit board within the body of the dryer. Unscrew this device from the back of the knob and disconnect the wires. A replacement timer costs a few dollars and should screw into place without trouble. Reconnect the wires and put the dryer back together. It should work fine now.
  • If you need a new timer the best place ti get it is from Rough River Appliance Repair
  • Phone number is (270) 230-1818 his name is Charlie and he is the best!

Nov 16, 2011 | Dryers

1 Answer

Bought a KB classics build & load track set. The small car fell apart when I thought I was putting in the battery. Instead when I unscrewed the car, the small motor just fell apart. There are...


i have the same exact problem, tried to put the gears back together myself and couldn't figure it out. i tried to see if i could just order another car car but no luck with that either. please let me know, as well

Jan 01, 2011 | Toys

3 Answers

End of toner life on Brother HL-2140


What you should do is look at the short sides of the toner. You will notice a clear round piece with tabs sticking up. What you need to do is color the inner part of the circle with a sharpie. This should give you another 100 prints or so. After you've exhausted that option, cover the spot a few times with electrical tape. What this is doing is block the "low toner" laser from shooting through these open spaces, tricking it into thinking it is full. Be sure to be observant; when the paper begins to look 'dirty' it is REALLY time to replace the cartridge. I've gotten up to 2,000 prints extra by doing this!! Good luck!

May 13, 2010 | Brother HL-2040 Laser Printer

1 Answer

My Kenmore dryer heats as it should but the timer dosent move and the dryer stays on.


This is a common problem. Dryer timers are advanced by a motor that turns gears and moves the dial (and internal switching) forward. The timer needs to be repaired or replaced. More than likely the latter since most timers are riveted together and cannot be repaired (unless you're someone who can put a geared jigsaw puzzle back together without any instructions since they normally fall to pieces when opened). I have tried to repair some timers and have been marginally successful, but to have a piece of mind, order the part, have it replaced (wire for wire when the unit is unplugged from the wall). If the timers look different, it is still possible that they gave you the correct timer. Verify that the new and the old timers have the same letter and number markings on each of the wires.

It is best to label the wires as you remove them from the old timer with a piece of tape and a sharp pointed marker. That way there is no question which wire is which.

Hope that helps you.

Nov 03, 2009 | Kenmore Dryers

2 Answers

Install new timer for pool about 5 weeks ago. clock does not work or timer. what do i do to fix problem?


Do not tirn the clock dial counter clockwise as it will brake the teeth on the plastic gear causing the clock not to turn. If the gear is broken The mfg. will mostlikley send a new one for free with an exploded view. It is very easy to replace. Don't forget to shut off the power first as the points will be exposed during your gear replacement.

Aug 17, 2009 | Intermatic & Indoor/Outdoor Rain Tight...

2 Answers

Repeated paper jams from the brother hl2070n after remove toner


  1. Remove left cover (where the USB connection is located);
  2. Remove big black gear with a spring on it (you may need to unscrew the PCB that partially covers it);
  3. There is a clutch that sticks to the rubber pad behind this gear. You may put a piece of scotch tape towards to a rubber pad, so the plastic from clutch mechanism would'n stick anymore. http://www.phillycopiers.com/fix/hl-2040-2070-fix.jpg

Oleg Andrukh IT Specialist
PhillyCopiers.com 215 364 3774

Apr 26, 2009 | Brother HL-2070N Laser Printer

1 Answer

I took apart timer cant out it back together


IF YOU DID THAT, I SUGGEST YOU GET A NEW ONE CHANCES OF YOU GETTING THIS BACK TOGETHER THE RIGHT WAY ARE NOT GOOD

Apr 11, 2009 | Dryers

Not finding what you are looking for?
NRS Mad Gab Mania DVD Game Logo

Related Topics:

1,087 people viewed this question

Ask a Question

Usually answered in minutes!

Top NRS Toys Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Tom Chichester

Level 3 Expert

61127 Answers

ray gallant

Level 3 Expert

71004 Answers

Are you a NRS Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...