Cant bond mobile phone to 6000cd unit

To connect Bluetooth on an Audi A4b6 CD player (Concerts 2), you will need to follow these steps:

1. Make sure the CD player is turned on.
2. Press the "Menu" button on the CD player to access the main menu.
3. Navigate to the "Settings" menu using the arrow buttons on the CD player.
4. Select "Bluetooth Settings" from the menu.
5. Follow the prompts on the screen to enable Bluetooth on the CD player. This may involve turning on the Bluetooth function on your phone and selecting the CD player from the list of available devices.
6. Once the CD player is paired with your phone, you should be able to use the Bluetooth function to make and receive phone calls, stream music, and access other Bluetooth-enabled features.

Hi
Normally when you try and connect or pair your device it normally ask for code. mostly its 0000 or 1234

thanks

Turn iPhone Bluetooth On:First you want to make sure that Bluetooth is functioning on your iPhone. Click on the Settings icon from the iPhone desktop. From the settings screen click General to show the iPhone General Settings as displayed in the below image. Notice you can see if Bluetooth is on or off from this screen. General Settings screen you can click on Bluetooth to configure the Bluetooth settings. On the Bluetooth screen shown below click to the left of Off to turn Bluetooth On.

1. Begin Uconnect Setup:Now that Bluetooth is operational on the iPhone you can start the Uconnect process. Click the Uconnect button on the rear view mirror to begin. The voice from the Uconnect system will ask you to verbally select one of the options from the menu. Once Uconnect asks for your input say "Setup" to begin the process of syncing the iPhone.
2. Start Phone Pairing:Once you say setup in the above step the Uconnect system will list numerous options available from the setup menu. One of these options is "Phone Pairing" so when the Uconnect system asks for the choices from the setup menu say "Phone Pairing".
3. Pair a Phone:In the Phone Pairing menu you can modify current entries or begin pairing a new phone. After Uconnect lists all of the choices you should say "Pair a Phone" to begin the process of pairing the iPhone.
4. Uconnect Pin Code:The first step in pairing a phone is setting the Bluetooth Pin Code that authorizes that phone to pair with the Uconnect system. When asked for the Pin Code say any four digit combination such as "1 - 2 - 3 - 4". Uconnect will repeat back the Pin Code so you can verify it has recorded properly.
5. Connect iPhone To Uconnect:After you have set the Pin Code for the Uconnect system you need to view the iPhone's Bluetooth Settings screen which you can get to following the steps in Step 1 above. Before the Uconnect system shows up in Bluetooth the Bluetooth Settings screen will look similar to the below where you may have other Bluetooth devices showing or not.After a couple seconds the Uconnect system will display as "Hands Free" as shown in the below image. Notice it states that it is not yet paired,,,,,
6. Click on the Hands Free device showing in the Bluetooth devices list above. This will open a new screen as shown in the below image that prompts you for the Pin Code you specified in Step 5.
   
   Enter the Pin Code and then click the Connect button in the top right corner of the above window. This will pair the iPhone with Uconnect and take you back to the Bluetooth devices screen where the Uconnect Hands Free device will now show Connected as shown in the below image.
   
   After the device is connected you will be prompted by the Uconnect voice again so proceed to the below steps.
7. Phone Name & Priority: After connecting the iPhone you will then name the phone and set a priority between one and seven. Name the phone anything you would like and if this is your primary phone set the priority to one so this phone always connects at a higher priority than any other phone.
8. Verify & Test:Now have a friend dial your cell phone while you are in your car to see if the music volume lowers and the Uconnect voice tells you there is an incoming call from a certain number. To make calls you can press the Uconnect button and follow the voice prompts.
The Uconnect system is a great way to safely use your cell phone in the car.

Check your owners manual, does the car have that option. If you still have questions contact the new car dealer.

you have to go into the menu - look for settings - bluetooth and delete listed unit.

If there is no mobile phone Paired to the
vehicle system and the SIG screen is
displayed, Pairing may be performed as
follows:
Select Phone Mode (if not already
selected).
Use touch-screen keypad to enter the
following digit sequence and press the
Send/End button.
The following sequence performs exactly
the same function, but times-out after
approximately five minutes, ##1#*#.
(If you are not familiar with the Pairing
process, this sequence is NOT
Recommended, because of the time-out
period.)
At the SIG**** screen the vehicle system
is waiting for communication with a
Bluetooth equipped telephone.
Check that your mobile phone is set to the
Jaguar Bluetooth system, using the menu
functions on the phone. Refer to the
handbook that was supplied with your
specific mobile phone.
When Jaguar device is found on the
mobile phone display, the phone will
prompt you to enter the pass key (1313)
on the mobile phone keypad.
When the above operation has been
completed and the phone is successfully
Paired and connected with the vehicle
system, the SIG* screen will be displayed.
S.Y.

jaguar parts dept can supply this very easy, contact the parts dept, they have manuals for what each car needs

read the manual

Are you sure the blutooth is active in your car? Contact the local dealer and have them run a "DCS" and confirm the car is fitted with Blutooth. Then go to www.bmwusa.com and check that your phone is apporved to work with the car. Provided nothing is wrong with the car you can then follow the instructions below.

1. make sure your phone's bluetooth is "always on"
2. get your phone all the way to the "search screen" and stop
3. press the "menu button on the radio
4. press the button below the "phone" in the menu screen of the radio.
5. press search on your phone to locate the car.
6. after the phone locates the car press yes to "bond"
7. the phone/car will now ask for a password, enter 1111 and press enter or ok.

Ifyour passwrd does not work you will have to go to the dealer to get the correct one or you can locate the TCU in the driver's rear inner panel in the trunk and get the number off the unit. It will say "PK XXX"

Contact your dealer. If there is something wrong with the car it will be fixed under warranty.