Fix for whirlpool tub problem

The following link explains step-by-step how to replace the drive belt on a Whirlpool Duet washer:

http://www.fixya.com/support/r3059652-drive_belt_installation_whirlpool_duet

This is a very simple procedure, but if you experience any difficulties, please post back and let me know. I hope this helps you.

For the model you have listed, changing a belt cannot be accomplshed by removing the back of the dryer. The following link explains step-by-step how to replace the belt on your dryer:

http://www.fixya.com/support/r3059469-install_dryer_belt_kenmore_elite

This can be a tedious process, but isn't difficult if you follow the steps provided. If you have any questions along the way, please let me know. I hope this helps you.

The manufactured date is deterimed by the SERIAL NUMBER on these appliances. The following link explains how to determine the age of Whirlpool manufactured appliances:

http://www.fixya.com/support/r2880489-determining_age_whirlpool_appliance

The first two NUMBERS of the serial number determines the week it was manufactured. The last digit before the numbers, determines the year. If you still have questions, please let me know. I hope this helps you.

NOTE: The serial number criteria is for all appliances manufactured by Whirlpool. Your washer and dryer will use the same format.

"F02" is a Long Drain error code. This generally means you have a clog or restriction in the drainage system somewhere. The following link explains:

http://www.fixya.com/support/r615268-f02_error_code_whirlpool_duet_kenmore

In the majority of the cases, all you have to do is clean out the drain pump reservoir. The instructions are included in the link I provided. If the problem does not go away after you have performed all these preliminary measures, the pump may be damaged and require replacement.

This error code gets generated if the drain cycle exceeds 8 minutes. If the pump impeller/motor gets damaged, the pump may not pump at the proper volume and the error code will continue to reappear.

A replacement (if required) can be purchased at any of the following websites:

searspartsdirect.com
appliancepartspros.com
pcappliancerepair.com
repairclinic.com

The pump is sold as a complete unit. You cannot buy just the motor.

If you have questions about this repair, or require addtional assistance, please let me know. I hope you find this information helpful.

This can be a finger buster. I put it on the motor pulley and roll it onto the tub pulley. I have seen others use a large crowbar to slide it over the motor pulley last but that seem risky to me. It is a very tight fit.
Eric

be sure that the tub is moving around with out the outer tub moving....could be a motor controller problem.....but heres the part#s tub assembly#8181912 youll want to replace the seal too. seal#8181673

You can go to;
http://www.appliancepartspros.com/partsearch/model.aspx?model_id=502723

to see the assembly and some prices of parts of your machine.

You can go to;
http://shared.whirlpoolcorp.com/product_literature/search_results.jsp?searchTerm=ghw9100lw1&siteCd=WHRCOM

to get owner's manual, parts list, etc.

The error code occurs if the pump does not drain within (I believe) 8 minutes. With the tub empty, you have no resistance from anything to obstruct the flow of water. With the tub full, its going to put a bit more strain on the pump to extract water. If the pump motor or impeller are damaged, it may be just enough to cause the pump to run slow enough while the tub is full and cause the error code. If you have already verified all the drain lines to be clear, and have no drainage issues with your household plumbing, the manufacturer recommends you replace the drain pump.

Go to searspartsdirect.com and type in the model number you provided. The pump will be located under the "Pump and Motor" heading as item number 10 (part #280187). It is only sold as a complete unit.

If you need instructions on how to replace the pump, please read this link:

http://www.fixya.com/support/r401845-replacing_drain_pump_whirlpool_duet

I hope this helps answer some of your questions/concerns. Let me know if you need further assistance.

I had the same problem and being a procrastinator, I waited until the belt came off before launching a full scale investigation into the knocking noise it had been making for about a year. Here is what I found and below that is my no guarantees fix.....
I removed the nut and pulled the tub pulley off. I noticed the tub shaft has a "shoulder bolt" and the pulley could not be tightened onto the shoulder bolt with enough squeeze to keep the tub pulley from wobbling. Tolerance issue... maybe? I decided to measure the keyed tub shaft with calipers and found the thickest part of the shaft to be 1" ish. The Shaft is part of the tub bearing assembly (from my observation) and the tub shaft is part of the tub bearing which measured 1 1/4" diameter. I found a washer that was 1" inside diameter and 1 1/4" outside diameter and placed it over the tub shaft behind the tub pulley. I tightened the nut snugly and reinstalled the belt. Ahhhhh, quiet operation and no more wobble. I will let you know if it causes another problem but from what I can tell.... replacing the tub pulley with another of the same dimensions will not work.

you don't need a very thick washer(my washer is too thick (.1"ish) so I will replace it soon(yeah right) with 1/32" or maybe 1/16"...I used rubber but I think steel or brass or what ever would probably work too.

Purists will tell you that the lock nut should be replaced, or if you don't use the permanent thread locker you could use loctite.

Hope that helps.

see this link to test it for issue
http://www.fixya.com/support/t364216-whirlpool_duet_ht_ghw9400pl0