I have a frigidaire, model ftf2140es0. It will not start. the top light (door lock) is off on the five light panel when i have the washer in normal. I tried to run diagnostic, but nothing happend. The lights stay lit. Sometimes there are three beeps. The start light is blinking.

https://www.appliancepartspros.com/repair-help/frigidaire-washer-ftf2140es0-repair/ftf2140es0-wont-start.html

This may help.

Check the part on the door that actuates the locking mechanism. It could be distorted or worn. Sometimes the lock assemblies need a tweeked adjustment. On the other hand if you don't hear a click, check the wiring.

Is the message "LOL" or "LOC"? I suspect the child lock "LOC" has been activated. To toggle this off, press and hold Options and Select for 10+ seconds. This feature prevents someone from accidently starting or changing a cycle selection.

There is a small padlock icon in the middle of lines linking the two buttons that let you toggle the child lock on and off.

There are two Frigidaire washers with the model ATF6000ES (the S is followed by a 0 or a 1). The manuals for both are available here: http://www.frigidaire.com/manuals?model=ATF6000ES . The child lock feature is described in the Operating Instructions. For the ATF6000ES0, the direct link to the appropriate manual is http://manuals.frigidaire.com/prodinfo_pdf/Webster/134604400.pdf . See page 2 under Washer Features.

I hope this helps.

Cindy Wells

Sounds like the electronic locking mechanism is malfunctioning. It is supposed to enguage before the high spin cycle. It is about a $20 part.

hello,


All error codes start with the letter "E". An error code of E11 will have the five indicator lights flash once and the Start indicator light flash once.


Some models of Frigidaire washers come with a digital readout display that informs the operator of the unit's function and any errors.

Error codes indicate that a problem has occurred and should be addressed. Different models of Frigidaire washers may vary in their fault displays.

Some washer models use flashing lights at the unit's start, door lock, wash, rinse, final spin and control indicators to display error codes.



If the five indica

tor lights flash more than nine times, this signals a letter in the error code. The letter "A" stands for 10 flashes, "B" for 11, "C" for 12, "D" for 13, "E" for 14 and "F" for 15 flashes. An error code of EB2 will have the five indicator lights flash or blink 11 times, and the Start indicator light blink twice

hope this help?

thanks.

Hi there, the same thing is happening with our washer. Did you find a solution to the problem? We found a coin the the black tube, but it still doesn't do the final spin. I can hear the motor trying to do something, but it just won't do the final spin. If anyone has any idea or suggestions it would be greatly appreciated. In the meantime, I have a load of slopping wet laundry to deal with. :(

The reed switch has been removed from the newer washers of same model. Nothing to do with the switch. Open door and turn the drum. This has happened to me a couple times. If the drum will not turn , try putting a little force on it. Mine acted the same and it was a sock that was stuck. Didn;t know what it was until I removed the boot where the coin trap is . and found a sock hanging down from the tub. stick your fingers up it the tub( with washer unplugged) and check for any material that might be there.

Yes - often times the plastic breaks from slamming the door.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

You're problem is probably the door latch assembly. This is a common problem on Frigidaire front load washers. You can find the part at your local appliance parts suppliers. If the door latch assembly is faulty, the washer will run through all of its normal cycles, but will not spin. Hope this fixes the problem for you.

check for a sensor switch located underneath the door , its a safety device to ensure that door is tightly closed . hope it helps