Question about Konica Minolta bizhub C351 All-In-One Laser Printer

1 Answer

How to reset image unit for C350 bizhub? - Konica Minolta bizhub C351 All-In-One Laser Printer

Posted by mehdi palangi on


1 Answer

Ty Schmidt

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Konica Minolta Expert
  • 118 Answers

Well there is a chip on the image unit that image unit (all colors) you need special chip writer to reset. you may need to just buy a new unit or drop me a line i may be able to get one...

Posted on Oct 31, 2011


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove error C0200 on bizhub c350?

C0200 - Cyan PC Drum Charge Corona Malfunction. Did you mess with this imaging unit? You won't be able to reset if the malfunction is still present.
Konica Minolta Error Codes & Solutions -
Drum, Transfer Belt and Fusing Unit Firmware Reset -
Drum and Toner Chip Reset -
Transfer Belt and Fusing Unit Reset Kit -

Aug 15, 2014 | Konica Minolta Office Equipment & Supplies

1 Answer

C 0001 code on Konica Minolta bizhub c350

Main Motor, recommend that you remove all of the image units, shake each one along its axis so that the developer in each unit is evenly spread across the units, so that not all the developer is sitting at one end, DO NOT STORE IMAGE UNITS UP and DOWN always lay flat. Might have already burned out the motor worse case the control board$$$$$$$$$$$$$$$$$$$$$$

Btw, I’m available to help over the phone in case u need at

Jan 08, 2014 | Konica Minolta bizhub 350 All-In-One Laser...

2 Answers

I have a trouble code C-3727 showing on my photocopier konica minolta bizhub C353. What does that mean?

C-0F36 on the bizhub C350 means the machine has registered a really low toner density in the Black
Imaging Unit. I'd take the unit out, give it a shake and pop it back in. Also worth checking you have some Black Toner in it.Or in case You Still Having Konica Printer Problem Then Follow Us For On: Konica Printer Support

Oct 06, 2013 | Konica Minolta Konica Bizhub C353 Drum...

1 Answer


C0202 on a Bizhub C350 means you have a Magenta PC Drum Charge Corona malfunction.
The charge corona is contained in the Magenta Imaging Unit. There are cleaning rods on each Imaging Unit. I would try pulling out the rods and cleaning the wires that way. Concentrate obviously on the Magenta unit. Run it in and out several times. Turn off the MAIN power switch (NOT the one up on the control panel) then back on to reset the code and see if it goes away. If not you may have to have your service company clean the Imaging Unit or it may have to be replaced depending on how bad it is.
Good Luck and Thank You for using Fixya.

Sep 19, 2010 | Minolta C350 Color Printer/Scanner/Copier

1 Answer

C350 bizhub image unit counter won't reset after changing

using a post:
1. With power ON, open the front door and locate the small, rectangular hole below the imaging unit removal tool.

2. Insert a suitable object into the hole to actuate the reset switch .
3. The code should clear and a message to close the front door should appear.
So all settings are RESET.
thanks for krishmaqvan

Dec 29, 2009 | Konica Minolta bizhub 350 All-In-One Laser...

1 Answer

My Bizhub C350 has locked due a imaging problem. There are solution without change the imaging unit?

once the machine locks you out for a imaeg unit you are done until the unit is replaced or reset chip is installed but there is new firmware that can be installed in the machine that wil not stop the machine from usage was the image unit has reached end of life so the next time a service tech comes out tell them you want the new firmwareand set image unit life to suspend

Dec 06, 2009 | Konica Minolta bizhub 350 All-In-One Laser...

1 Answer

How to reset the copier after installing the new imageing unit c350

Normally it has no need for reseting.
In the moment you put the new image unit it resets the counter life, although you can reset by holding down the trouble reset button and in the screen you will see trouble reset.
touch it and switch in and off the machine with the main power button.

May 15, 2009 | Konica Minolta bizhub 350 All-In-One Laser...

Not finding what you are looking for?
Konica Minolta bizhub C351 All-In-One Laser Printer Logo

664 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6960 Answers


Level 1 Expert

54 Answers


Level 3 Expert

85239 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides