Error...Quick Service Code 00-83. Also, what does G3RED in Mode column mean?

Its a black unit error code
It means the black toner is not supplying to d developer you can reset error code by logging in d service mode

The Ricoh copier error code SC551 / 551 is a fusing thermistor 1 error code.

It can mean:
1. The thermistor is not connected
2. The thermistor connector is bad

To reset this error try the code:
"Clear Mode"+107+"Clear/Stop" hold for 5s.
Turn ON and OFF the Main Switch.

If the problem persists you may need to contact a local service technician to take a look at your copier.

http://basketballgames.io/
Basketball Games, you are the all star team. Do quick match, tournament or even play against your friends in 2 player mode. Call your friend right now, set your team and get ready for super struggles which are tough from each other.

him that error mean there is temperature error. you need to clear that error from service mode first.
press aditional function
press 2 and 8 at the same time
press aditional function
service mode should appear in the screen
select COPIER / FUNCTION / CLEAR / ERR and press OK
disconnect the machine for 5 seconds
turn the machine on and make some copy test

Family error code E50 means a problem with the washing motor. Family error code E70 means a problem with the NTC sensor. In my experience, E50 is most common fault in worn carbon brushes. But in any case family error code E50 is shown to the customer. In service mode could be: E51,52,53 and 54. The same applies to family E70 error code that will be displayed in service mode as error code E71 or E74.
E50 error code could be: motor winding, power board, tachymetric generator, motor relay on power board, wiring between motor and power board and wiring between tachymetric generator and electronic.
E70 error code could be: faulty NTC sensor, wrong position of NTC sensor or to much limescale on it and finaly wiring between NTC and electronic.

Dado

That error mean there is a sudden change in the fixing unit temperature.
First clear that error from service mode. Press additional function
press 2 and 8 together
press additional function agian
service mode should appear in screen
select copier
select function
select "clear"
select "err"
select ok.
unplug power cord for a few seconds and restart the machine
try to make some copies if problem persist replace the fixing heater assembly

That's a fuser temperature code that will need to be cleared in service mode. Press the additional functions key * then press 2

Hi brittruiz07, I’m an owner like you and will try to help.

Is your machine type a FAV6800AW or FAV9800AW? I need to know the model number this is important.

With this condition I assume both lid locks retract allowing you to open the lid and no water flows into the wash tub and you take no error codes to the display is this correct?

The Lid is Locked LED lit and if the water valves are not not signaled on at the start of the wash cycle this issue could be related could be related to a Control Board issue. I don't want to say failure just yet. Let's see if the Control Board will let you get into Service Mode. With no error codes to start the troubleshooting process with we need to enter Service Mode and vview machine Error Code History.

To enter Service Mode press and hold simultaneously the Enviro Plus and Spin Only keys for three seconds or until the control beeps and the display reads “00”.
This is from the Service Manual; this process starts on page 17 in the Service Manual.
In Service Mode press the Wrinkle Control key.
The display will show a “d”.

The diagnostic codes can be viewed by using the Set Delay Time arrow keys. Pressing the Set Delay Time down arrow key will cycle down the list one code at a time each time it is pushed. Please right down each code such 4, 18, 22 etc.
If there are no error codes in the Control Board memory the display will read “- -“ that’s two dashes in the display. I feel you will have many Error Codes from previous wash cycles. I just want to get a feel for the Error Code history.
Next I want you to hard reset the Control Board by pulling the disconnecting the washer power cord for ten seconds then reconnect washer power. Go back into Service Mode and make sure all Error Codes have cleared you should only see “- -“. Press the off button to back out of Service Mode.
Start a Quick Wash cycle with minimal machine settings and no clothes in the basket.

If the washer fails to start the Quick Wash cycle as you described in your initial post how long did it take for the machine to unlock the lid? Did any water flow into the tub and were there any Error Codes sent to the display? Please go back and read the error code list and let me know what error codes you see from this Quick Wash cycle attempt. I know this is painful but we need to start somewhere.

You can pump out excess water when you fail with dc/UC unbalance errors with this process from the Service Manual.

Close the lid and enter the Service Mode by pressing and holding simultaneously the Enviro Plus and Spin Only keys for three seconds or the display reads “00”

Press the Delicates key this will lock the lid.

Now press the Presoak key the drain pump will turn on.

Turn off the drain pump by hitting the off button or hit the Presoak key.
Rich

Also this code needs to be cleared in service mode. Despite what the display says, turning it off and on will not reset it. To enter service mode insert a straightened paper clip into the small hole in the front cover, near the meters, a "$" sign will appear on the display. Press * 4 * in order. Press ">>" to select "error" then press "OK" then power cycle.

(I cant remember on that model but you may need to defeat the interlock on the front door in order to enter service mode.)

The error code is saying you have a fuser fault
Try resetting the machine

get into service mode

then COPIER
then FUNCTION
then CLEAR
then ERROR
then OK at the bottom right hand corner
if you dont know how to get into service mode
call me 00447764303923.