Nordic Track NordicTrack A2550 PRO Treadmill Logo

Related Topics:

Question about Nordic Track NordicTrack A2550 PRO Treadmill

1 Answer

I have a nordictrack a2050. the console doesn't

Posted by Woody on

  • Robert Adcock
    Robert Adcock Jan 27, 2018

    Were you able to fix this problem? What fixed it? Mine is doing the same thing

  • Vincent Callender
    Vincent Callender Jul 09, 2019

    Mine is doing the exact same thing, is there a fix?

×

Ad

1 Answer

Kenneth Simmons

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,238 Answers
Ad

5 Related Answers

Anonymous

  • 14 Answers

SOURCE: nordictrack apex4100i level incline will not work

Try this calibration procedure.
Turn the power switch on. Remove the safety key. Hold the Stop and Speed Up or Speed Plus buttons down then insert the safety key.
The display should show some numbers.
Press the stop key one time and the display should show some other numbers and some 00's. Press the Incline Up button and see if the Incline begins to move, if it does let it go all the way up and then all the way down, wait a few seconds after it stops, then hit the stop key 4 times. It should be calibrated. If it didn't move then the board or the incline motor is bad.

Posted on Jul 08, 2009

Ad

Anonymous

  • 40 Answers

SOURCE: Nordictrack motor will not run when start button is pushed.

Likely the cover of one of the motor brushes popped off. Unplug the machine before you pop it back in place, then try it again.

If that doesn't work, most likely it's the motor control board, or possibly the console, or finally just a loose connection behind the console.


But most likely, it's the motor brush cover. I've been seeing that alot with this model.

Posted on Nov 01, 2009

maxtreadmill

John Mazmanian

  • 832 Answers

SOURCE: I have a Nordictrack a2050 model NTl10851,seems

Sounds like the actual function pad is causing the problem in some cases you'll be able to purchase that part and sometime with iconfitness you have to buy the entire console for a hefty amount you may call them @ 1-800-999-3756 or go to their website iconfitness.com. Good Luck

Posted on May 14, 2010

maxtreadmill

John Mazmanian

  • 832 Answers

SOURCE: Pro Form Treadmill 625 EX Wide Trac

1. You may have a worn belt and deck problem ( #1 problem on treadmills ). Test by the following procedure:
a) without the power on stand on the walking belt
b) push the belt in the direction it normally turns
c) if the belt is very difficult to turn (on most treadmill) this means that you have high belt/deck friction.

You must physically inspect the belt and deck. The deck should be smooth. The belt should have a consistent feel from side to side (a belt can be worn out without any sensory signs of a problem). If you feel deep grooves in the deck or uneven wear on the underside of the belt, part replacement is necessary. Continued use of your treadmill may damage expensive electrical components. If their is no signs of excessive wear then the next step is to lubricate the deck follow this procedure:

Before applying lubricant, the belt must have the tension reduced and cleaned deck. Loosen the tension roller by following the instructions in your owner’s manual. Do not loosen the bolts in the tension roller too far or the bolts will come out of the roller shaft. This step may not be necessary for your treadmill model or belt and deck condition.
Contaminants are the worst enemy of your belt and deck. Some treadmills may have an excessive accumulation of dirt and contaminants. If these are trapped during the belt lube process, significant damage will occur. Lift the belt and slide a moist towel between belt and deck, slide the towel the length of the unit to catch the contaminants do this a number of times inspect towel and need be use a fresh towel and repeat cleaning let dry then apply the lube in the center upper third of deck then start unit and walk on it @ 1-2mph for about 5 min. You may purchase the lube from National Gym Supply @ gympart.com Part# TM001 or call them @ 1-800-496-7278 their on the west coast. At this point I believe your problem should be resolved if the above procedures have taken care of problem take a look at the next step, as mentioned the #1 cause of treadmill failure is lack of maintenance of the belt and deck.

On occasion, you may have already damaged the DC board if you have high belt/deck friction. If the belt walks freely, you have a different problem.

2. If it passes the belt/deck checks, you may have a DC board output problem. If the belt tests ok and you have a speed variation, try this test:

  1. Set the speed to 2.5 MPH. Let the treadmill run without anyone on the belt. Check to see if the speed is constant or if there is a variation.
  2. If there is no variation, step on the belt. If the speed slows down or speeds up, you may have an output problem on the DC board. This is the board that connects directly to the motor. Check the speed sensor if it is a magnetic sensor unit ( Under motor shroud usually attached on the left hand side of frame with 1/8' clearance between sensor and front roller pulley) you can test continuity with a multi meter or replace with a new part to test. Many times passing a kitchen magnet in front of the signal will make a speed display on the console if the magnetic sensor is good.

Posted on May 16, 2010

Anonymous

  • 42 Answers

SOURCE: NordicTrack T5.3 belt stopped working. It's only 1

HI, its seems like the belt on the motor has either slipped off, or you just need to tighten it. best way to find out is to take off the front pannel showing the motor. then stand on the treadmill. start it and you will see the problem.

Posted on Nov 21, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

NordicTrack ASR1000 console doesn’t work

How To Repair a NordicTrack Elliptical
  1. Pulse Sensor. Peel off the plastic. ...
  2. Console. Charge the battery pack by pedaling the elliptical for several minutes. ...
  3. Pedals Squeak and Stick. Loosen screws on the side shield using the Phillips-head screwdriver. ...
  4. Tightening and Loosening the Drive Belt
https://www.livestrong.com/article/159137-how-to-repair-a-nordictrack-elliptical/
https://www.youtube.com/watch?v=s779SR-kCko
0helpful
1answer

Nordictrack 5.7 buttons don't work

Call the 800 number on the front of your owner's manual (downloadable at iconservice.com) for service. Most likely your console is shot. It is easy to swap out, but costs a little bit. Also, make sure your safety key is on. Consoles do not operate without that little red key in the front.
0helpful
1answer

NordicTrack Treadmill A2050, Will not work at all, with key in place.

1) test the receptacle wall, plug a desklamp for to see if work if is working go
2( testing the power cord for open or defective.
3) reset the machine
4) test the fuse for blown and replace
5) test the c.breaker for tripped and reset again.
6) test the key, the key is small magnet, you can test with your magnet refrigerator with atraction or repulse, if doesnot replace the magnet from home depot.
God bless you
9_20_2012_11_40_41_am.gif
0helpful
1answer

NordicTrack Treadmill A2050, Will not work or turn on.

1) test the outlet wall , put a desklamp and see if work, if work the problem will be in the machine,
2) test the fuse inside for blown and replace with the same capacity
3) reset the circuit breaker inside.
4) test the power cord for open or defective.
Try again, if the machine NOT work, the problem will be in the power supply see the block atached.
God bless you

9_20_2012_5_08_41_am.gif
0helpful
1answer

I have a nordictrack audiostrider 800 that i just replaced the console. now the resistance won't work. thoughts?

The way to tell if your NordicTrack digital console is bad is to troubleshoot it first. If nothing works, you've got a bad console. The digital console is an important part of exercising. A manual machine will still work even if the console doesn't, but an automated machine needs the console to work so you can adjust things like speed, resistance and incline. You also can't use programs or see your time, distance or estimated calories burned without a working console. The two most common reasons that a console will be dim, display bad results, or won't turn on are bad batteries and a problem with the reed switch.

  1. Replace the Batteries
    • 1 Replace the batteries first, if your machine has batteries. A manual machine such as the NordicTrack MTN 740 will not need batteries, and instead the console is powered by your moving the steps. Check your manual if you are unsure of which batteries to buy. Different machines will require different batteries. The NordicTrack Mini Stepper uses watch batteries, but larger machines will likely need AA or D batteries.
    • 2 Take off the cover to the battery compartment. Remove and discard the old batteries. Replace all of the batteries, not just one if you happen to have one good one. Align them correctly with the "+" and "-" signs as shown on the compartment.
    • 3 Replace the battery cover and attempt to turn on the console.
    Reset the Circuit Breaker
    • 1 Check the circuit breaker. A machine such as the NordicTrack CXT 990 will have a circuit breaker located on the front of the machine. The console will not work if the circuit breaker is tripped.
    • 2 Push the circuit breaker in if it protrudes until it sticks.
    • 3 Try to turn on the console. Check the circuit breaker for your house if this does not fix the console problem.
    Adjust the Reed Switch
    • 1 Inspect the reed switch as the information on the display will not be true if the reed switch is too far from the flywheel on NordicTrack machines such as the MTN 740.
    • 2 Unscrew the two M10 by 82mm button bolts on the right pedal bracket. Unscrew the two M10 nylon locknuts. Pull off the pedal bracket and set aside.
    • 3 Remove the two M4 by 38mm screws. Remove the three M4 by 25mm screws. Slide the right side shield off to expose the flywheel, magnet reed switch.
    • 4 Unscrew the screw that holds the reed switch in place but do not remove it. Slide the reed switch toward the flywheel but leave enough space that the magnet can move freely. Replace the shield and bracket
0helpful
1answer

Cant close my nordic track a2050.... its stuck open...not very space friendly

Does it close part-way? If so, it might be the same thing that happened to me. Make sure the incline is at zero. It will not close if the walkway is raised.

If that doesn't work, you might try disconnecting the incline motor screw (held in by a retaining pin and cotter pin), turning the screw one or two rotations and reconnecting it. I've had to do that in the past, but I'm sure it is not an approved solution.
0helpful
1answer

I have a Nordictrack a2050 model NTl10851,seems now,as i got used only the 3,6,10 mph keys work on the control panel.Also the incline controls do not work at all.just wondering what might be the problem,or...

Sounds like the actual function pad is causing the problem in some cases you'll be able to purchase that part and sometime with iconfitness you have to buy the entire console for a hefty amount you may call them @ 1-800-999-3756 or go to their website iconfitness.com. Good Luck
Not finding what you are looking for?

3,330 views

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

David Shaub

Level 3 Expert

2994 Answers

Narseman

Level 3 Expert

1088 Answers

The Knight
The Knight

Level 3 Expert

76851 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...