Question about Hotpoint Ariston WD440G Front Load All-in-One Washer / Dryer

1 Answer

Machine did have f03 error, i checked thermistor and its ok, switched it back on now no warning lights but it auto filled and started a wash cycle, cancel and off buttone stop it but as soon as you turn on it starts again, machine now full of water, i cleared the filter out and checked pump working too

Posted by peter allen on

Ad

1 Answer

Richard Roth

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hotpoint Master
  • 9,472 Answers

Sounds like you have a stuck button on the display.

Posted on Oct 19, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

F 03 showing on machine


Yes F-03 indicates a faulty thermistor (it's inside the heating element at the back). Before calling an engineer, just open the bottom rear panel and check that the connector has not come loose (OR IN MY CASE FALLEN OFF COMPLETELY). This can happen if there is a spin cycle that runs out of balance big time. (two thin wires on a square unit about 5mm in size fitted to the middle of the heating element).

Jul 06, 2010 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Code F/o3 keeps coming up at the end of the cycle and machine just stops working


Error code F03 indicates that the wash thermistor is open or short circuit.
Check the connections to the thermistor

Jan 20, 2010 | Hotpoint Ultima WF840 Front Load Washer /...

1 Answer

F03 error message on Hotpoint WT741


Error F03 indicates that the wash thermistor is open or short circuit.
Check the thermistor, heater and connections.
Hope this jelps.

Jan 09, 2010 | Washing Machines

1 Answer

Hotpoint Ultima automatic washing machine, half way through wash cycle the display flashes F 03. The machine is less than 2 years old.


Error code F03 indicates wash thermistor open/short circuit.
Check all connections on thermistor and associated leads.
Hope thisn helps.

Nov 27, 2009 | Washing Machines

1 Answer

Error code F-03 Indesit wixe127


Hi.
The code F03 means the wash thermistor is open circuit.

Unfortunately, you will have to call an engineer.

Cheers.

Nov 18, 2008 | Washing Machines

1 Answer

HOTPOINT KEEPS FLASING F-03


The error code F03 indicates that the wash thermistor is open or short circuit.
Check heater element and thermistor,if ok, then you need to call an engineer.

Sep 22, 2008 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Wd640 hotpoint washer dryer - error code F03


This indicates that the wash thermistor is "Open Circuit" and I think it is situated on the heater assy at the back of the machine.

Check the wiring and contacts between the thermistor and the PCB. If you still get the fault it could be the Thermistor ( which means replacing the heater ) or a faulty board.
If it is under 5 years old - Call Hotpoint as you have a 5 years Parts Guarantee mind you the call out is £89.98 but thats cheap if it happens to be the board!

Mar 14, 2008 | Hotpoint Aquarius WD640 Front Load...

3 Answers

Indesit WIE 147 - Display 'F-03' fault


Indesit washing machine error code 3 (F03) On certain Indesit washing machines, if the on off light is flashing 3 times, with a slight pause, followed by flashing a further 3 times, or if it is didplaying F03 you have an error code that is explained as follows -
NTC fault - check Thermistor and module connections.
The NTC is the thermistor, which is a modern-day thermostat. It’s inserted into a tube in the heating element and is filled with heat sensitive crystals that change their electrical resistance according to their temperature. By knowing what electrical resistance the crystals have at given temperatures they can tell the water temperature.
With this fault the NTC is either faulty, or there’s a dodgy connection to or from it or there’s a connection problem where it connects to the main PCB.
It’s not something you can easily fault find yourself unfortunately, apart from if there was an obvious broken wire.

Feb 10, 2008 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Hotpoint Ariston WD440G Front Load All-in-One Washer / Dryer Logo

390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

Richard C Cohen
Richard C Cohen

Level 2 Expert

171 Answers

gbob59

Level 3 Expert

3063 Answers

Cindy Wells

Level 3 Expert

6220 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...