I have a NV-DX110B about 11 years old. I'm getting

. Error Codes Panasonic JVC Description F01 . No Take-Up reel rotation F02 E03 No Supply Reel rotation F03 E02 Mechanism has not unloaded to the Eject position F04 E01 Mechanism has not fully loaded up to the stop position F05 E04 Rotation of the video head has stalled or too fast . E06 Tape drive motor is not rotating or stalled F31 . Data Transmission error F51 . Focus drive motor is not functioning, no focus. Color F52 . Zoom drive motor is not functioning, no zoom U10 . Dew Sensor has detected condensation or failed U11 . Video Heads have been detected as clogged failed

check your mode switch that may have jumped a tooth

go to panasonic.com/vcr and give them the model/serial # and ask what the F03 error code means and they can give you a solution for the problem.
Jerry

The following list of codes indicates an electronics communication problem with the washer: - Duet HT washer - F01, F03, F06, F11, F23, F24, F27, F28, F29, F30, F31, F32, F35, F42, F61, F62, F63, F64, F65, F70, F71, and F99

If Pause/Cancel does not work:

1. Unplug washer or disconnect power for one minute.
2. Plug in washer or reconnect power.
3. Re-select the cycle and press Start.

NOTE: If the error remains on the display, call for service.

I would first replace the door latch/lock assembly, a number of users have and it fixed the F-11 error code completely. Its the cheapest part for this problem.

Hope helps.

Have you found any solution to the F01 error? I just got the same issue. Thanks!

Panasonic JVC Description
F01 No Take-up reel rotation
F02 E03 No Supply reel rotation
F03 E02 Mechanism has not unloaded to the eject position
F04 E01 Mechanism has not fully loaded to the stop position
F05 E04 Rotation of video head has stalled or to fast
E06 Tape drive motor is not rotating or stalled
F31 Data transmission error
F51 Focus motor is not functioning, No focus
F52 Zoom motor is not functioning, No Zoom
U10 Dew sensor has detected condensation or failed
U11 Video heads have been detected as dirty or failed
Matti Knuutila [email protected]

I saw this same issue. I would unplug and plug in the DVD and it would still show error code F03.

It turns out that one of my kids had shoved a couple of small objects inside the VHS opening and it was blocking the operation. I removed the objects and it works fine.

This error code is not listed in the manual that came with the DVD player.

check to see if theres something inside otherwise you have to bring in for service

Both of these error codes are related to the reels inside of the camcorder. The error codes that you mention stand for No Take Up Reel Rotation (F01) and No Supply Reel Rotation (F02). The take up reel is the one that pulls in the extra slack while the tape is running so that the tape itself does not become loose and choppy. The supply reel is the reel in charge of turning to allow the tape to unwind. What you are experiencing are both common reel rotation errors.

First things first, restore your camcorder to factory settings, take out the battery and leave it out over night, plug it back in the next morning. If that doesn't fix it, try a completely different tape that you've used in the camcorder before to see if there is something wrong with the tape reels (sometimes they are loose) or the tape itself.

If that does not work, your next step is cleaning the camcorder. Use a cleaning tape. You may want to perform two or three cleanings in order to make sure that the camcorder is back to normal. You can also use an electronics dusting brush and manually clean out any visible dirt or dust, sometimes blowing cool air (such as the canned air used to clean computer keyboards) directly into the camera can fix the problem as well.

Unfortunately, if neither of these solutions fixes it, it's time to take it to a repair shop, it may need a new reel mechanism inside of the camcorder.

Good luck!

Panasonic K deck F03 or F04 shows in display check loading motor coupling pt no VDP1434 or motor pt no VID12128 £11.95 CHS