Question about Canon W8200PG InkJet Printer

Pc and printer wont talk to each other

Hi i have just bought a Canon W8200 wide format printer but i cant get my pc to talk to the printer. I have just done an ipconfig on my pc and i have found my ip address, the submask and the default gateway. when i put these values in the into the printer it will not print. I was told that when i put the ip address in the printer to change the last digit but to keep it in the same range, so i changed 2 to 3 on printer and still no joy. i have also tried a ping and i am getting timed out messages. i have tried crossover cables too and still no good. I cannot consult manuals as it was bought second hand and i did not get any installation software, but have downloaded the drivers from canon. i also have tried running through a wirelss router but yet again still no joy. any intructions to solve this problem would be appreciated and even though i'm not a computer whizz i can work my way around a pc (just) i am running windows xp thanks

richard barker May 29, 2006

hi

thanks for your help but still no joy.

got a little bit further on the driver install as the w8200 came up in a "add printer" window.

when i used the utility program i had to re-input the ip,subnet mask and g/w default back in to the printer menu.

I did a ping on ip,subnet mask and g/w default which test ok, but the ip that printer is set to, i get timed out messages.

i have tried all combinations of crossover cable and normal ethernet cable. i have tried direct from pc to printer and through a netgear wireless router with both cables.

any more ideas?

thanks in advance

×

1 Answer

Clifford Hardy

Level 2:

An expert who has achieved level 2 by getting 100 points

Hot-Shot:

An expert who has answered 20 questions.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.
Expert
111 Answers

FIRST GO HERE http://www.usa.canon.com/opd/controller?act=OPDSoftwareAct&fcategoryid=2333&modelid=9506 GET THE DRIVER AND THE SETUP UTILITY THEN HOOK UP THE PRINTER TO THE ROUTER THEN YOUR GOOD.

usa.canon.com

imagePROGRAF W8200

Posted on May 28, 2006

1 Suggested Answer

6ya staff

2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

6ya.com

Instant Repair Help over the Phone

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

Access service mode w8200

keep trying man you'll get it please keep trying

Aug 17, 2013 | Canon imagePROGRAF W8200 InkJet Printer

I cannot find drivers for My W8200. I am using Windows7 64bit

There are no drivers yet for Canon imagePROGRAF W8200 on windows 7

Jan 22, 2011 | Canon imagePROGRAF W8200 InkJet Printer

Printer driver canon W8200 64 bit

Hi, please get new driver here: www.driversdown.com/
www.nodevice.com/driver/company/Canon/Printer.html
www.usa.canon.com/cusa/office/products/.../hs_1200ts

Jay mnkas

Jun 17, 2010 | Canon W8200PG InkJet Printer

I have an error on my w8200, on the screen

i have an error on my w8200, on the screen written ERROR E20D01,
what is the code mean?

Jun 04, 2010 | Canon W8200PG InkJet Printer

I own a canon w8200 pigment large format printer. I replaced two cartridges, Magenta and Yellow. The printer did a nozzle check that seemed to take too long. I then received a 'waste ink tank full'...

<Remedy>
1.Waste ink absorber
Use SERVICE MODE>COUNTER>PRINTER>W-INK to check the waste ink
absorber. Replace if the waste ink level is near the limit (14400).
After replacing the tank, perform SERVICE MODE>INITIALIZE>W-INK.

Apr 04, 2010 | Canon IMAGEPROGRAF IPF8000 InkJet Plotter...

Canon W8200 error message "Print Head Error" "turn off printer"

There was no response to the question, so we called in a Canon service person who has ordered a replacement print head.

Nov 24, 2009 | Canon imagePROGRAF W8200 InkJet Printer

Canon pixma ip3000inkjet printer

The printhead is clogged.

See the following guide:

Canon iP3000/4000/5000 Printhead Cleaning Guide

If it does not work, replace the printhead: Genuine Canon Print Heads

Nov 25, 2008 | Canon PIXMA iP3000 InkJet Photo Printer

Error code on canon w8200

Clean the round rod that the print head moves along and also the metal work above where the carrage rollers run.
I wipe mine with a drop of oil after cleaning as error is indicating that the carrige is sticking and not moving at the correct speed.

Chris

Mar 19, 2008 | Canon imagePROGRAF W8200 InkJet Printer

Canon imagePROGRAF W8200 InkJet Printer Problem Printhead Error! Turn Power Off!

you need to enter a service mode before the error message pops up. hold down paper source button + online.
that should override the message before it pops up.
go to replace print head selection. or do a clean. it may still be working. let me know if this doesn't work....but at least you can still get past the message now! marty

Oct 27, 2007 | Canon imagePROGRAF W8200 InkJet Printer

Need to pack up amd move W8200

Canon have a specific protocol to be followed to prepare the printer for transport. It is shown in a pdf file I downloaded from http://www.usa.canon.com/html/download/ipw8200.html.
the file is in the Guides section

Jan 27, 2007 | Canon W8200PG InkJet Printer

Not finding what you are looking for?

View Most Popular

W8200PG InkJet Printer

Office Equipment & Supplies

Related Question

Access service mode w8200

Canon imagePROGRAF W8200 InkJet Printer

Open Questions:

error plotter canon w8200 pg

Feb 03, 2014 | Canon W8200PG InkJet Printer

I have a Canon W8200 and i get the error message "E02805 Check Y Tank " I have tried 3 new tanks and still no fix, I even had a canon technician out here for 2 hours, he was as usefull as **** on a bull. can anyone help

Jul 29, 2011 | Canon W8200PG InkJet Printer

E0280C error check M tank on Canon W8200. shut doen printer and error still appearing. need immediate assistance

Jan 30, 2010 | Canon W8200PG InkJet Printer

W8200 IP PROBLEMS hi i have just bought a Canon W8200 wide format printer but i cant get my pc to talk to the printer. I posted a question yesterday and was told to download the canon utility. I got a little bit further on the driver install as the w8200 came up in a "add printer" window. when i used the utility program i had to re-input the ip,subnet mask and g/w default back in to the printer menu. I did a ping on ip,subnet mask and g/w default which test ok, but the ip that printer is set to, i get timed out messages. i have tried all combinations of crossover cable and normal ethernet cable. i have tried direct from pc to printer and through a netgear wireless router with both cables. any more ideas? thanks in advance

Mar 24, 2017 | Canon W8200PG InkJet Printer

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Check Out the Latest Printers Report

View all Fixya Reports

Top Canon Office Equipment & Supplies Experts

Clive

Level 3 Expert

4345 Answers

old marine

Level 3 Expert

2261 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for Canon W8200PG InkJet Printer? Or just drag it here!

Loading...