Model of the phillips tv x04636 21'' wooden was not found on line, i used the above to pass over my problem to you experts to help find a solution.
the screen of my tv lights with no raster and sound.
the channel display is also off. where does the problem lie.
eargall waiting for you troubleshooting guide.
best regards,
sam wepukhulu
An expert who has achieved level 3 by getting 1000 points
Superstar:
An expert that got 20 achievements.
All-Star:
An expert that got 10 achievements.
MVP:
An expert that got 5 achievements.
Master
1,476 Answers
Re: No raster, No sound
Your problem discription is not very detailed but certainly it sounds like the first place to look would be at the fuses if the set is completely dead. Good luck.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Check and replace damaged component/s at its horizontal scan output section circuit. Check the LOT (Line Output Transformer) too for damage. Replace the horizontal scan output transistor. Check the input voltage to LOT. If the voltage is absent check the feeder resistor; if any. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/
There is no raster to your TV I assumes. If the LED drive inverter board has damaged, there will be no back light, and so no picture. If sound is OK, suspect the inverter board. Check this for more details.
Hi Sikandar, Let me know how many times red led blinks as there would be an interval of 3 seconds so count blinks from pause to pause. Is it Sony AR25M61 model or any other? Above info will help to diagnose problem. Thanks.
Go to the Anantek website and search for your TV or similar TV's to see if anyone has posted repair hints. I've fixed several TV's and other electronic equipment from their website.
Hi there Let's make ur problem a bit clear. "white lines" how? where? meaning retrace lines with full raster or a single vertical line? buzzing sound? without even turning the power switch of the TV to "ON" or when u just plug the power cord? I'll check for schema, mean while can u tell me where the resistor leads to? is it a fusible resistor? if so , to which area the resistor suppliers power? Regards Rifaa
That unit is a PTV916 chassis.
The oscilating sound you hear is probably a feedback pulse on the secondary transformer. That would first make me suspect that the HOT (Q802 / 2SD1556)(horizontal output transistor) has shorted. You need to check for any short between the base and emitter pins of that component. If that's the problem properly replacing it should restore normal operation.
If that wasn't it, you would next check for failer of the SSB located on the left side of the unit next to the tuner, mounted vertical. That board has been a problem in many of the PTV9xx series chassis. It can be rebuilt, but will take some extensive knowledge and equipment to test.
If any of this sounds too complicated I strongly suggest a qualified shop do the testing and repairs. If you have any difficulty locating a reputable shop try contacting NESDA (National Electronic Service Dealer's Assn.) for a listing of shops in your area. It is worth repairing.
Good Luck
Bill
This denotes a problem called blooming the horizontal lines you see are called retrace lines this is caused by the increase in anode voltage which could be caused by an increase in HV section current which trips the overcurrent protection dircuit and turns the TV off.If you do not have electronics experience I would suggest taking the set to a TV repair shop.
wepu, Buddy it sounds like you got a power supply problem. As you say the picture is all blue?? With no video or sound and the fact that the channel display is out is the first indication that i would guess this. Do you still have the owners manual that you got when you first got the set? Good, cause thats the only place i can think of where to look in case of service over in your part of the world as I did try!! Man I tryed but to no avail. No one has heard of this model but that dosent mean that it dos'ent exsit!.. If your a tech or know your way around solid state circuitry then you should have no problem finding the fault once you get a service manual from the service location in your owners manual. Now if your not a tech and a handy man ?? If I were you I wouldnt mess with the tv as theres over 25000 volts inside the set and i've seen it make a grown man cry. Man dont attempt the repair or troubleshooting if you dont have the right or proper tools and equipment!!! Good Luck
×