Belkin (F5D8231-4) Wireless Router (F5D82314) Logo

Question about Belkin (F5D8231-4) Wireless Router (F5D82314)

1 Answer


Posted by tito1764 on

1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 114 Answers

Reset your router back to it's factory settings by holding the reset button for about 5 seconds. I have provided a list of the most popular router brands. If it does not work you may need to google what your specific model's default IP address/default username/default passwords are, for example search for "Encore ENHWI-2AN3 default IP address" The default login info can change, it can depend on where you obtained your router. If you purchased it yourself from a store then the standard defaults should work. If you obtained your router from your Internet Provider you may need to contact your service provider. It also may depend whether it's an old or new model router as well. And you may need to press and hold the reset button on your router several times before it actually clears. Make sure you have a wired connection then once you have accessed your router simply run the Setup Wizard. Set your SSID as something you'll remember like "Mavericks Network" and your Password can be something like your phone number for example 3109876543

Belkin - Username: Leave the field blank Password: Leave the field blank Default IP address is:

Buffalo - Username: root Password: Leave the field blank Default IP address is:

D-Link - Username: admin Password: Leave the field blank Default IP address is:

Encore - Username: admin Password: admin Default IP address

Linksys - Username: admin Password: admin Default IP address

NetGear - Username: admin Password: password Default IP address will be: or

TP-Link - Username: admin Password: admin Default IP address

TrendNet - Username: admin Password: admin Default IP address

Zhone - Username: admin Password: admin Default IP address

Zyxel - Username: admin Password: 1234 Default IP address

Posted on Sep 08, 2011

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


I have a 2007 kia amanti i removed the fog lights they were blown now i cant replace them area is to small to work in do i need to remove the front upper grill assembly and the the entire front lights...

Hmm. Dude, if you managed to remove them, then you should do the same process in reverse :-)
Sorry, but this really isn't a good question. I mean you know what's the problem and also managed to solve it, but you don't know how to put back something on it's place, what you just took mounted off?

I have spark and injector pulsing, but injectors 1 and 6 pulse slower then rest of cylinders causing slight ruff idle. No trouble codes.

Way out of my league here iam afraid ,now if it had a distributor and a carb then i could give you a good answer but these new fangled things ,now firstly i would check the ?? hmm thinking no cannot be that signal going to the computer unless the crank was broke timing belt? hmm NO as valves would hit piston ,HMM aloud going to make the tea whilst i think about it ---apple crumble and custard ,lovely and my mind is still a blank and stopping smoking for 5 wks now doesnt help either anyway enough of my drivel but i think in a case like this try another ECU as inside this unit is a chip that controls the spacing of time between the initial pulse sense from the crank sensor and then the spacing for the other cylinders ,1&6 would pick up the pulse if iam not mistaken as the end cylinders normally go up and down together but not on all 6 cyl engines though ,depends on if its a inline or a V ,Be careful in changing the ECU from another vehicle as you may need the chip from the key and transponder reader from the donor vehicle and a seperate transponder reader box on some earlier models as this is a american vehicle of which i have no practical experiance .Now to drink my tea before the next question

Hmm..just got PreSonus "TubePre" and

The signal SHOULD be line level which you can run into most any line level input. This level is considerably higher than a mic by itself...around 50 Db or so higher.

Cannot print from my PC

hmm basically make sure its your defualt printer on pc. try goign to control panel system hardware , device manager and removing the usb hub that the printer is pluged into by uninstalling it and restart pc. make sure its not only default printer in the software that runs the printer but also defualt printer in control panel and printer settings, try another usb port. hmm no more ideas . hope this helps

T41 does not go past the splash screen on boot up! Help

Does the computer emit a series of long and short beeps when you first power up? if it does, download the HMM, the Hardware Maintenace Manual, from IBM/Lenovo's site for your model. Inside the HMM a beep code to possible cause table will give you more information.

And be sure your RAM cards are free of lint, etc., and properly seated in their bays.

Upgrading processer in thinkpad t30

I have IBM T30 laptop and my Laptop having problem of display its shows when open any files its open like viberation

The top screen on my ds doesn't work all it does it is stays white what do i do

hmm same here. my brother dropped it. ive tried shaking it and stuff. it disappears after a while
Not finding what you are looking for?


Ask a Question

Usually answered in minutes!

Top Belkin Computers & Internet Experts

Donivan Wise

Level 2 Expert

254 Answers


Level 3 Expert

4383 Answers


Level 3 Expert

3290 Answers

Are you a Belkin Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides