Canon MultiPASS MP360 All-In-One InkJet Printer Logo

Question about Canon MultiPASS MP360 All-In-One InkJet Printer

1 Answer

PRINTING HAVE RENEWED BOTH INK CARTRIDGES BUT NOW IMAGES COME OUT GREEN AND A LITTLE DISTORTED(LOOKS A BIT STRIPEY) PRINTER IS ONLY 18 MTHS OLD AND HAS NOT HAD A LOT OF USE. CAN YOU HELP. THANKS. MAUREEN.

Posted by MAUREEN FITZGERALD on

  • joeval Nov 27, 2007

    After changing a new ink, the printer print funny, the print-out somewhat distorted.

×

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 38 Answers

Probably bad color cartridge, try relacing again in a new one

Posted on May 21, 2006

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
2answers

Get the esp 2170 to not print light green instead of black ? I keep on replacing cartridge , to no avail !

replacing a cartridge, while the nozzles are blocked won't help.
Realise the printer will mix there colours to get "black" on the paper. So even a full cartridge, can't make the other colours black till the blockage is gone.

Please try this. If you have ink cleaning fluid, (only for printer ink) use that, if you dont have cleaning fluid, use clean water.
Open the printer as if you replace a cartridge. Remove the black one and look tot the bottom of the cartridge holder. There is a little pipe, where the ink should go in. put some drops water or cleaning fluid in there leave it a few minutes. with a tissue dry it and again insert some drops of water or cleaning fluid. Then put in a cartridge and give the printer a black and white print job. Like print a few A4 papers. Let it print till the black comes back. Can take up to 4 pages A4. I hope this will unblock the nozzles.
Please even if you don't need to print, switch the printer on at least once a week. And even better, let it do a bit of printing every week. This will save a lot of frustration.
0helpful
1answer

Lexmark 730 not printing

Regarding the Lex1 cartridge's no printing/severe fade (or similar) during printing, my answers are provided below:

For the poor print quality problem (degraded image quality) you are observing, we suggest you first visit the "Print Quality" page of the "General Information" section of the Inkjet 411 website and follow the suggestions provided: http://inkjet411.com/?page_id=1432

A. 1. Cartridge & Printer maintenance should also be evaluated - ensure both ink cartridges and flexible driver contact cables (where the cartridge interfaces to the carriage inside the printer) are thoroughly clean: http://inkjet411.com/?page_id=1519

A.2. Perform a hot-water flush on the suspect ink cartridge, refer to video procedure here: http://inkjet411.com/?page_id=1519

A.3. Run a quick test print to evaluate cartridge performance (i.e. 4-color test print):
http://inkjet411.com/?page_id=146

For information on North American ink refill services (for Lexmark 1, 2 and 3 ink cartridges) at a major retailer near you (should you wish to save ~50% on ink costs), general printing problem resolutions or advanced Lexmark printer diagnosis procedures (advanced cartridge diagnostic tests/cartridge error bypass & printer reset methods, etc.), please visit Inkjet411: http://www.inkjet411.com
0helpful
1answer
0helpful
1answer

Not good colour consistency over an A4 page

I suggest you find a way to align the cartridge. If it contains alignment utility it should give you a better printout. Also check if you have enough ink on your cartridge. Uneven colour usually is due to lack of ink in the cartridge.
0helpful
1answer

Printing problems with epson stylus 800

you should replace the ink cartridge or you can clean it by using tape and peeling it off of where the ink comes out
2helpful
4answers

Hp officejet 6110 not printing with black ink

Hi lilacky-

Here are some HP support links that might be helpful... and a couple questions to consider.

Q: Is your new cartridge one of these listed below?
"The HP Officejet 6100 series and HP Digital Copier Printer 410 products use the print cartridges listed below:
* HP 56 black print cartridge
* HP 57 tri-color print cartridge
* HP 58 photo cartridge (replaces the HP 56 black print cartridge for six-ink photo printing)" info from: Installing a Print Cartridge
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00004340&lc=en&dlc=en&cc=us&lang=en&rule=12548&product=79477 Is your new cartridge a refilled cartridge? Some times those have special challenges. Has your cartridge been sitting a while in the box, maybe in a warm spot? Some times even new cartridges dry out a little. Was your old cartridge low or completely gone? Just as a test, if you put it back in your printer does the old cartridge work? Any printer error messages? Can you print a test page or an alignment page for your black cartridge? These might be too many questions but here are some HP support links with some How To information for getting more answers. Please let me know if any of these are helpful. see also: Slow or No Response from Printer
http://h10025.www1.hp.com/ewfrf/wc/documentSubCategory?rule=11882&lc=en&dlc=en&cc=us&lang=en&product=79477 -JW
0helpful
1answer

Blue ink - printing problem

Hi,
Your Cyan cartridge is empty and need replacement. Maybe you can clean head of Cyan cartridge with alcohol but symptoms are the empty cartridge!
Good luck.
0helpful
2answers

Restart after replace ink cartridge

my CX4800 has done the same thing. I ran the utilities dozens of times, replaced every cartridge and it feeds papers the print head moves like it's printing but nothing is imaged on the paper.
Searching the web is my last chance to fix it before i toss this 18 month old printer and never buy an epson again.
11helpful
6answers

Error e5

Isnt e5 error meaning the cartridge has been previously used before?? Best bet is to hold in both the colour and black copy buttons for about 5 - 10 seconds and this should allow you to print again. If you do not have a copier/scanner, hold in the resume button. (triangle within a circle).
Not finding what you are looking for?

52 views

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4362 Answers

old marine
old marine

Level 3 Expert

2420 Answers

Cindy Wells

Level 3 Expert

6627 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...