All VCR features work. Will record, but no image is displayed or recorded. The lens cap is off. Battery at full power. Tape in. Camcorder will actually record black/blurred but there is no picture in display or being recorded.
An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 500 times.
Re: Camcorder will record but no image...
Its a stuck iris assy an iris cucuit fault or many small pana cpsm that go bad all the time in these unit. Mke sure the iris didnt het seitched to manual andif it is i auto try tappin the lens a littlethe see if it opens Good luck
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
i know exactly whats wrong! the same thing happend to me.
1. turn off the gl1
2.look at the record button with the lock and standby switch
3.flip the switch all the way to standby because it might be stuck in the middle
4. turn on your camera
Dear carooooo, You are dealing with tape not film. Your problem might be in your tape.
Try running your tape on record the full length. Keep your lens cap
on. Color balance and use new tape that's for your Sony.
first check the iris of the camera if it is opening,you will see this when you look inside the lens of the camera when you turn on and off the switch at camera mode if the iris is opening....if the iris is ok the second problem may occurs of your camera is the ccd image sensor....
You may have a problem with the image sensor device (CCD). From October 3, 2005 through October 2, 2007, Sony will repair, free of charge, affected products exhibiting the above-mentioned problem where it is caused by the image sensor device. Sony will also cover the cost of shipping and handling from and to addresses within the United States and US Territories for service to correct this issue.
To see if you have this problem:
Power On your camcorder (make sure the battery is fully charged).
Check the LCD screen and verify that the display icons are turned on. If you cannot see the icons, press the Display button until the icons are visible.
Put a tape in the camcorder.
With the lens cap off, record some video. NOTE: Be sure to speak during the recording so the video will contain your voice.
Rewind this section of the tape (using tape counter to verify start of your recording).
Play back the recorded video and use the LCD screen on the camcorder to view it. You should hear the audio you recorded and the Display icons/text will still appear.
If your camcorder is affected by this CCD issue, the picture will either be extremely distorted, or there will be no visible picture (just a blank LCD screen with the display icons still visible).
There may be a simple explanation. Here are two possible reasons this is happening:
* You may have disconnected the power source before turning off the power to your camcorder. If you remove the power source from the camcorder while the power is on, all settings and selections will be erased. Make sure to turn the camcorder's power off before disconnecting the power source.
* This is particularly an issue for some early VHS-C camcorders – those with model numbers beginning with a "6" and ending with a "2" or "3" (i.e. CC6xx2 … CC6xx3). These camcorders have a consumer-replaceable clock battery that may be exhausted. If that battery runs dead or is removed and the main battery or AC is not connected, the camcorder will lose all its Date and Time settings.
* In some models, the date and time display is designed to do this.
When you turn on many VHS-C and digital camcorders, the Auto Date mode will display the time and date. When recording begins, the date is recorded on the tape for 5 seconds and then disappears. In the viewfinder, the date will then be replaced with the words AUTO DATE but they will not be recorded. They remain in your viewfinder so that you know this feature is on.
On full-size or VHS camcorders, the Auto Date feature is very similar. When you first turn on the camcorder, the date along with the word AUTO and a Clock icon appear in the viewfinder. When recording begins, the date is automatically recorded for 10 seconds and then disappears. In the viewfinder, the Clock icon and the word AUTO remain but they will not be recorded. They remain so that you are aware that this feature is on.
When using the Auto Date feature, be aware that the time is only recorded when you first turn on the camcorder and begin a recording session. It does not record each time you press the record button.
There are a number of time and date display and recording options. Since these vary by model number, please refer to your owner’s manual for more details.
# You may not have turned on the camcorder to record properly. For camcorders that feature both Automatic and Manual recording, make sure you press in the LOCK button while setting the POWER switch to the desired setting, either "A" (Automatic) or "M" (Manual) record mode.
# Automatic recording places the camcorder into Auto Shot™ mode, while Manual recording mode allows you to control many of the camcorder's special features, including accessing the menus and setting the clock.
# For many other camcorders, make sure the CAMERA/OFF/VCR switch is set to CAMERA.
Make sure the Erase Protection tab is in the position that allows recording. If not, slide the tab. Some tapes have removable tabs. If the tab has been removed, simply cover the hole with adhesive tape or use another tape.