Codes for a sany bravia and dish network box please

I would first look at Candy CDI 2D36 Washing Machine/Dishwasher NTC Thermistor and change it
parts are here https://www.4candy.co.uk/cdi-2d36-32900565/catalogue.pl?path=634342&model_ref=11868785

Hi there Gonzalez897! This is Kimberly with DISH and I ran across your post and would like to assist you. Some of the codes that can be used to program the DISH remote to a Sony Bravia tv would be: 500, 590, 640, and 781. Here is the link to our website, containing this information and also the steps on how to program the remote control to your tv.http://www.mydish.com/support/program-to-tv-code-non-basic I hope you find this helpful. If you need further assistance or have additional questions feel free to email me directly at [email protected]

Kimberly. Escobar
Social Media Representative
[email protected]


















































[email protected]

You didn't mention the model of the Dish receiver, so here are some common Sony codes. To reprogram the remote, press and hold the "TV" button on the remote until it stays lit. Enter one of the following codes and press "#". Check all of the functions. 500,640,652,756,758,781,783,795,796,797,798,806,807,837,844,845.

Hello,
The codes and instructions are different for each of the Dish Network boxes. In order for us to give you a direct and comprehensive instructions, we would need to know the model number of your Dish Box as well as the device (TV) you want to program.

If you prefer to look this information up, you can visit the Dish Network Remote Control instructions posted on their site: http://www.dishnetwork.com/SupportSection/remote-setup

Please let me know if I can further assist you.

Regards,
KYTechnology

Hi whetstonetylI was going over your post and seen where you need the codes to your SonyBravia TV. The codes that go with the Sony Bravia are; 500, 640, 758, 796, 670,690, 515, 678, 514, 11, 254, 578 and 255. If the codes I just gave do not workwe have what we call a Power Scan and I will leave a link to help with those steps.http://www.dishnetwork.com/SupportSection/power-scan-instructions

Hello, I hope that this has been resolved, but if not, here are some simple troubleshooting steps. You can follow the link below, which will walk you through doing a power scan to get the correct code, or you can input am 3 digit code with these steps:
1. Hold down the clear TV button until all lights light up at top of remote
2. input the code
3. Press the # (pound) button below the number 9 on the keypad
4. Press SAT button.

Here are some codes as well that you can try: 500 837 808 090
Hope this helps!!!

http://www.dishnetwork.com/SupportSection/power-scan-instructions

Becki Barned
DISH Network Customer Service

Masking tape over the ir sensor on the tv or turn off all energy savers.

The Sony RM-YD029 Remote control will work with the Dish Network VIP722 DVR HD Satellite Receiver, but the Dish Network VIP722's Primary remote address must be set to 1.

The procedure below will allow Sony RM-YD029 remote control to operate Dish VIP722.

Using the Dish Network Remote Control -
1. Press menu 2 times to get to system info page
2. In the system info page the primary remote address is in a white box (bubble) followed by a Green TV (1)symbol that says IR and indicates you the channel your remote control one is configured. The Sony RM-YD029 will work when this primary remote address number (in the white box) is set to 1.

If the Primary Remote Address of your VIP722 Remote control 1 is not set to channel 1, here is how to change it:

1. While displaying the system info page, press and hold the SAT button on your dish network remote until all other modes are flashing, about 3 seconds.
2. then press the '1' button on the numeric pad of your dish remote
3. then press the '#' button on the numeric pad of the dish remote
4. then press the 'record' button (red dot button - stores setting)
5. At this point you should see a number 1 in front of the primary remote address on the dish system info page

Ensure you enter the corresponding IR code into your Sony remote control per the instructions in the manual or Sony's web site. My 722 works with Sony IR code - 01775.

If you are looking to have the Dish remote operate your TV, just do a random search for your tv. First, hold down the tv button on the dish remote until all the rest of the light up. Next press the tvpower button on the dish remote. Next, press the channel up button (this is the up arrow button) until the set turns off. When it does turn off, press the # key at the bottom right of the remote. The tv button will light and flash twice. That's it. Your done. Hope this helps.

Refer to page 82 in your Dish Network User's Guide......(Make sure Sony system is powered on and in DVD mode with a disc in the player).  Point Dish remote at Sony box -  Hold Aux until all buttons light up at top....press 2 - then STAR button* and then POWER button - then press the up arrow key repeatedly until Sony turns off - press # key to lock in code.
It took me awhile to get it to work....it will only work power, mute, and volume - not dvd play functions. Refer to page 85 to make the Dish remote control the Sony box volume by default.
Good luck.