Question about Fisher and Paykel WA37T26G Top Load Washer

1 Answer

Hi, I have a fisher and paykel washing machine model #WA37T26G and I noticed yesterday and today that the lights lit on the electronic board was 1,6,7,8...not sure if it was the same yesterday and not sure if it will be the same the next time I use it, but today those were the lights, if you can give me any info. or anything regarding this, I would appreciate it. Thank you in advance.

Posted by nightowl26 on

Ad

1 Answer

keith jones

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Fisher and P... Master
  • 747 Answers

To work out the fault code go from right to left far right light is 1 the next is 2 next is 4 then 8, then 16,32,64,128. add up which lights correspond to your machine and then you can google that code and find what your problem is

Posted on Oct 26, 2017

Ad

5 Related Answers

Anonymous

  • 146 Answers

SOURCE: Fisher & Paykel GWL10 US won't spin

If the machine still has water in it, the drain pump is jammed or there may be an obstrution in one of the hoses. It is most likely the drain pump. Switch off the machine at the wall and unplug it. Tilt machine against a wall and look underneath. On the right you will see the drain pump. It looks upside down. Unplug the wiring harness to the pump and remove pump by turning it clockwise while at the same time releasing the little white clip that holds the pump in place. Clean thoroughly and replace pump.

Posted on Nov 03, 2007

Ad
aborcass

Ron Coons

  • 2651 Answers

SOURCE: Fisher & Paykel GWL10 US won't spin

its possible that the pump is either going bad or there is somethin gin the pumps/sump assy. on this model the unit generally tends to shut down when the pump overheats, and will only restart when the pump cools off, a warnig obout replaing hte pump if need be is the pump is actually 220v. you MUST UNPLUG MACHINE BEFORE SERVICING. its a foriegn brand remember so theres abuncha wierd wiring and the pump is one of them!

Posted on Mar 25, 2008

JULIANFIX

ALBERT GARCIA

  • 975 Answers

SOURCE: fisher & paykel (mw511)

check out the DRAIN MOTOR PUMP , its a small motor with 2 hoses connected to it , it could be clogged , need to remove it , inspect inside the impellers for any debri , clean it , re install and try again , hope this helpful AJ

Posted on May 20, 2008

Anonymous

SOURCE: Fisher & Paykel GWL10 US won't spin

Buy an new one and trash this one

Posted on Sep 13, 2008

Anonymous

  • 145 Answers

SOURCE: Fisher Paykel washing machine model # GWL15 drips

Hi Dale..
It sounds like you have a leaky inlet valve assembly. The part number is 421029P and is easy to replace. You can get one here:
http://www.fisherpaykelparts.net/ecart/item.php?item_id=266&category_id=56

Posted on Apr 20, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fisher and Paykel, EcoSmart with lid lock. After initial fill, all wash lights go out, advances to rinse, then beeps continuously. Have to shut machine off and start over. Continues to wash, but leaks...


Fisher and Paykel, EcoSmart with lid lock. After initial fill, all wash lights go out, advances to rinse, then beeps continuously. Have to shut machine off and start over. Continues to wash, but leaks out of top panel under lid. Machine is level. Any Suggestions?

Jul 28, 2011 | Fisher and Paykel WA37T26G Top Load Washer

1 Answer

My fisher and paykel washing machine is not starting a cycle as it is not getting any water. The pipes are turned on and is properly connected. It results in service light(spanner icon) flashing with a...


Hi just read your posting.Now when the machine beeps do any lights light up to indicate an error code?You have mentioned the spanner shows up but do any others light up as the machine is beeping?Please reply with additional information and I am sure I can help you.Looking forward to your reply.

Oct 04, 2010 | Fisher and Paykel WA37T26G Top Load Washer

1 Answer

Washing machine pumps intermittedly when filling up and then wont progress to the next cycle it stats beeping and 2 lights come on one each end of lights board


Hi just read your posting.Could you please confirm the model number of your machine for me.Now you mentioned in your posting the 2 lights that are lit when the machine is beeping are the 1st in the row and last.These lights are in a row of 8 lights so starting from the left to right the lights that are lit are 1 and 8.Is this correct?Please reply with aditional information on the questions and I am sure I can help you.Looking forward to your reply.

Oct 03, 2010 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Similar problem...


i don't know how old your machine is, but if it's still under warranty i'd get on it now! it could be failed electronics or loose/corroded connections.
you'll probably need a tech to trouble-shoot it. you may want to consider replacing it. it may be more cost effective!

good luck!

Jun 28, 2009 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Have kelvinator smart drive 503, water won't run


Hi,

I have exactly the same issue, which first appeared yesterday. Following your advice, the lights that are lit are 3rd, 5th, 7th and 8th. The SLOW & HOLD spin speed lights are lit, along with constant beeping :)

Jun 16, 2009 | Fisher and Paykel GWL11 Top Load Washer

Not finding what you are looking for?
Fisher and Paykel WA37T26G Top Load Washer Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

peter gittos
peter gittos

Level 2 Expert

247 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...