Washer wont drain or spin. Thewasher will agitate.

Washing Machine Will Not Agitate or Spin - Home Repair ...

? 15:00
www.youtube.com/watch?v=wUSmUSWWIS4
Oct 20, 2013 - Uploaded by Robert DIY This washing machine would not agitate or spin. There is a ...My washer also is not agitating or spinning but water will drain after a long while.

Troubleshooting Why the Washer Won't Agitate ' PartSelect ...

? 3:10
www.youtube.com/watch?v=LfWRyt1vj2w

Nov 5, 2012 - Uploaded by PartSelect
The only wash cycle that works is delicate none of the other washcycles work .... The washer still fills, drains and spins to dry butwill not agitate. ... Hi My machine wont spin or agitate on heavy loads like a few towels etc (fine

try this
http://forum.appliancepartspros.com/washer-repair/345592-kenmore-90-series-washer-wont-agitate-spin.html
Kenmore 90 series washer won agitate or spin Appliance Repair Forum

Hello.


If your washer is indeed a WFL2066, than the not spinning is directly relatedto the unit not draining.

These machines by design cannot spin if the drain is inadequate.

Here is the first step in resolving the problem, you need to access the drainpump/filter to clean it.

To reach the filter and clean it...

**Unplug the washer from the dryer or wall, or turn off the 30amp breakerat the home service panel...safety first**

1) Open the small square plastic door at the right bottom of thewasher.

2) Via the small hose drain any access water from the pump...this is where a wet/dry shop-vac comes in handy, or a shallow pan with a few towels works as well.

3) Then turn the pump insert/button trap counter clock-wise and pull out.Clean the trap out thoroughly running it under hot water and mild soap or your washer detergent and inspect inside the pump for any other foreign objects/obstructions.

4) Re-install the lint trap insuring it is good and snug/tight. Before closing up the small access door, run a short rinse spin cycle to check forleaks.


Thank you for visiting our site please take a moment to rate the info-provided for you here.

Thanks.

Hello.


If your washer is indeed a WBSE3120B, than the not spinning is directly relatedto the unit not draining.

These machines by design cannot spin if the drain is inadequate.

Here is the first step in resolving the problem, you need to access the drainpump/filter to clean it.

To reach the filter and clean it...

**Unplug the washer from the dryer or wall, or turn off the 30amp breakerat the home service panel...safety first**

1) Open the small square plastic door at the right bottom of thewasher.

2) Via the small hose drain any access water from the pump...this is where awet/dry shop-vac comes in handy, or a shallow pan with a few towels works a swell.

3) Then turn the pump insert/button trap counter clock-wise and pull out.Clean the trap out thoroughly running it under hot water and mild soap or your washer detergent and inspect inside the pump for any other foreignobjects/obstructions.

4) Re-install the lint trap insuring it is good and snug/tight. Before closing up the small access door, run a short rinse spin cycle to check for leaks.

Let me know how you make out, or if you require further assistance.

Thank you for visiting our site please take a moment to rate the infoprovided for you here.

Thanks.

with this many issues it sounds like the timer has a dead spot in it,especially your saying it wont even fill,then wont drain or spin,but only agitate

If the machine fills, won't agitate, wont drain or spin, then you need to replace the lid switch.
if machines fills, wont agitate, will drain but not spin, then you need to replace the motor coupling

Hi, Do you know if the washer agitated at all? If the washer does not agitate or spin, the coupler is most likely the cause. If the washer agitates and does not spin, it could be spin basket drive or transmission.
Please let me know so I can assist you further.

Vic

Replace the lid switch.

unless your washer is over 20 years old, then it wont have a belt. the temperature of the water wont have anything to do with it spinning or not.
need to know if it agitates or drains and just wont spin.
if it agitates but no spin or drain, then you have a bad lid switch.
if it wont agitate or spin, but will drain, then you have a broken drive coupling.

You can check the drain or the filter. You will have to pull it out of the space it is now to access it. Items will get stuck in the drain clogging it.