How do I clone the MAC address in a Router? - SMC Barricade 7004

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Scholar:

An expert who has written 20 answers of more than 400 characters.

Hot-Shot:

An expert who has answered 20 questions.
Expert
130 Answers

In the routers web interface, click on login (password would be either blank or smcadmin) -> Advanced setup -> click on WAN -> Dynamic IP address -> click on clone MAC address and save the settings.

Posted on Feb 19, 2006

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1helpful

1answer

Purchased new 3g router for wireless access to internet. Can't get on to internet? Have checked forums and followed suggestions none work todate. Laptop and broadband wireless modem works fine without...

You may need to clone your MAC address, a unique address is for each device connected to a network. Some internet service provider (ISP) modems quit working if the MAC address of the device connected to its Ethernet or LAN jack (i.e., your computer) changes from the one used when it was first set up. So when you hook up a new router to share the connection, you run into the problem you have.

Cloning the MAC address in the router sets it to the same address as the device connected to its number 1 wired port. Since you didn't give the brand and model of your router I can't give you specific steps or links to follow for the process. But it's typically very simple. From the computer originally used to set up your modem, access the router's setup pages. On the appropriate page, pick "clone MAC address" from a menu or click on a button. You can search for "<insert your brand of router here> cloning MAC address" and find many sites with how-to information. A good starting point is always the router manufacturer's site, where there is probably already an answer in their support FAQ section.

Once the router MAC address has been cloned, you should have your Internet access back and will be able to use the wireless access.

Once the MAC address in t

Read full answer

Mar 20, 2011 • NetComm Computers & Internet

0helpful

1answer

Need to mate my rotor with my cable internet

You need to get to the web configuration page of your router and clone the MAC address of your modem. It's because cable internet providers uses MAC address of a device to be able to connect to their server.

You can follow this manual to access the web configuration tool and look for the topic MAC Cloning Address.

http://downloads.linksysbycisco.com/downloads/WRT54GL-EU_11_UG_A-WEB.pdf

If in some case, your internet didn't work after connecting the router and after cloning the MAC address of your modem. Try to turn off your modem and disconnect everything from there, turn off your router as well and disconnect everything. Wait for 1 minute and plug the power cord back to your cable modem and plug the ethernet cable. Wait for 1 minute, turn reconnect everything to your router to the modem, and Clone the MAC address again.

Hope this helps.

Read full answer

Jan 13, 2010 • Linksys Wireless-G WRT54G Router

0helpful

2answers

Unable to connect to Comcast router

access the router page and set to router mac address using PC mac address, for detaiks call zonet tech support

Read full answer

Aug 11, 2009 • Zonet (ZSR0104UP) Router

0helpful

1answer

I have a Netwave Base G4 wireless router w/ 4- port switch,trying to network two computers via cable modem using local ports,modem and router not communicating

You need to change the LAN IP address of your router. Open the router's admin through http://192.168.1.1 and look for router's IP address or Local IP Address. Change it to 192.168.10.1 and save the settings. Reboot the router after that. If you are on cable internet , you need to do MAC Cloning. Access the router's admin page and look for MAC Clone settings. Enable and clone the PC's Mac Address. Save the settings and power cycle the router and the modem after that.

Read full answer

Aug 02, 2009 • Blitzz Technology (BWA611) Router

0helpful

1answer

MAC address

Why do you want to clone the router's MAC address?

If you want the router's MAC address, go to the Admin (I believe it is) page.
That button is for cloning your Desktop or Laptop computer's MAC address, and unless you are being instructed to, there is no need to.

Read full answer

Jan 19, 2009 • Linksys Wireless-G Broadband Router

0helpful

1answer

My Dynex 4 port router will not communicate with my DSL modem

Have your router clone the MAC Address of your computer. The MAC address is a hardware address on your network card and DSL providers seem to like to bind it to account. What is probably happening is when the router connects to your ISP and asks for an IP address, it looks up your account info and and decides - nope, wrong device. Cloning the MAC address will make them happy. If you are not able to clone the address, call your provider's tech support and ask them to clear the MAC address from your account. Make sure you have the router plugged into the modem and not the computer or you are back to where you started.

Read full answer

Jan 05, 2009 • Dynex 4-Port Ethernet Broadband Router...

2helpful

1answer

MAC address cloning

Hi killer - MAC (Media Access Control) cloning is used to clone your MAC address.
Some ISPs (most notably MediaOne) use your NIC's MAC address to authenticate your service. When you change the computer that you have connected to your cable modem service, you usually have to call up Tech Support and give them the MAC address of the NIC in the new machine. Since hardware routers have the equivalent of a NIC on their WAN port in order to connect to your cable modem, you would have to do the same thing if you're installing a router.
Recently, however, some ISPs have started to recognize the MAC addresses of popular routers and disconnect service if a router is detected. Fortunately, many router manufacturers are including the capability to either set the router WAN port MAC address to anything you want, or copy it from a computer connected to the router LAN side. You can check the Router comparison chart under "Mac addr. clone" to see which routers support this feature. Then consult the router's documentation for directions on using the feature.
So basically, it's used to fool ISPs into thinking there isn't a router. If the router has the same MAC address as either your NIC card or your modem the ISP won't detect and service won't be interrupted. Most ISPs don't do this so iy's rarely needed.
If this answers your question PLEASE rate this as fixed. If you need more help just add a comment and I'll be happy to assist you further. Thanks.

Jeff

Read full answer

May 22, 2008 • Belkin (F5D7230-4) Router (587009)

0helpful

1answer