Connection Issues Occur When I Try to Connect Through a Broadband Network Adapter

Here's how to configure your wireless settings:

1. On the console, go to My Xbox, and then select System Settings.
2. Select Network Settings.
3. If you are prompted to select a wireless network, complete these steps, otherwise skip to step 4.
   1. Select the name of your wireless network.
   2. Enter your wireless network password and select Done.
   3. The console will automatically try connecting to Xbox LIVE. If you get an error message, go to the following webpage for help: support.xbox.com/pages/xbox-live/troubleshoot/connection-issues/connect-xbox-live.aspx (http://support.xbox.com/pages/xbox-live/troubleshoot/connection-issues/connect-xbox-live.aspx)
   
   Note If you do not see the name of your wireless network, select Advanced Options. Then select Specify Unlisted Network and enter your wireless network name. Select your wireless security type (WEP, WPA, WPA, or No Security). This security type needs to match the security of your wireless network.
   
   
4. Select Configure Network.
5. On the Basic Settings tab, select Wireless Mode.
   
   Note If wireless mode is not available and you are using the black Wireless N Networking Adapter, try using the software installation disc included with the adapter. For more information about how to do this, please see the following article: 977641 (http://support.microsoft.com/kb/977641/ ) How to set up the Xbox 360 Wireless N Networking Adapter
6. Select Scan for Networks.
7. Select your wireless network name.
   
   If your network is not listed, try the following:
   1. Select Specify Unlisted Network, and enter your wireless network name (also referred to as your Service Set Identifier [SSID]).
   2. Select your wireless security: WEP, WPA, WPA2, or No Security (if your network doesn't have a password).
      
      If you can't connect to your wireless network, try improving your wireless signal using the tips in the following article: 909336 (http://support.microsoft.com/kb/909336/ ) Your Xbox 360 console receives a weak wireless signal
8. Enter your wireless network password, and then select Done.
   
   Note Make sure that you have entered the correct password. An incorrect password might allow your console to connect to your wireless network, but you might receive an IP address error when you test your Xbox LIVE connection.
   
   
9. Press B on your controller, and then select Test Xbox LIVE Connection.
   

I am having the exact same problem today. Here is the link to the driver.

http://go.microsoft.com/fwlink/?LinkId=33104

This will install the Microsoft Broadband Network Utility which will allow you to install the card.

Neeraj

http://support.microsoft.com/kb/814445

Try this out and see if it isnt the bee's knee's .

Dont forget to rate me, thx

lets see here, your NVIDIA thing is for your ethernet port in your computer.

the wireless PCI adapter, is well, a wireless adapter, its used to connect your wireless, and a 1394 Net Adaptor Connection is basically Win2k/XP's way of telling you that you have a Firewire interface installed in your system.

so, if your going wireless, you dont need NVIDIA, and as your device manager shows that it has a red x on it, it shows that its disabled. as for everything else, i wouldent worry about it.

three is the network
connect and install three usb modem
connect xbox to pc with ethernet cable
then start right click my network places and go to properties in network connections right click 3 usb modem then properties then advanced, tick the box allow other network users' then okay
now connect 3 3g device turn on xbox and BINGO !

Back up base station settings Before you start, back up the current settings for your base station. To do this, follow these steps: 1. Start the Microsoft Broadband Network Utility. 2. On the Tools menu, click Management Tool. 3. When you are prompted to, log on to the base station. To do this, use the password that you created when you ran the Setup Wizard the first time. If you did not run the Setup Wizard, use the following default base station password: admin 4. On the Management menu, click Back up and Restore Settings. 5. Click Back Up Settings. 6. Click Save. 7. Type a name for the file that contains your base station settings or use the default name Config.bin. 8. Click the folder where you want to save the file, and then click Save. Back to the top Back to the top Disable firewall or antivirus programs For information about how to disable your firewall or antivirus programs, view the documentation that came with the program, or contact the manufacturer's technical support. Back to the top Back to the top Install firmware update Warning Do not install the firmware update from a computer that is connected to your base station by using a wireless network connection. If your wireless signal is interrupted, weakened, or interfered with while the firmware update is running, your base station may become unusable. Automatic update 1. Start the Microsoft Broadband Network Utility. 2. On the Help menu, click Check for Updates Online. The Broadband Networking Update Service checks for updates by connecting to Microsoft. This can take several minutes, depending on your connection speed. If any new updates are available, a download screen appears. Otherwise, you receive a ?No new updates are available? message. 3. Follow the instructions on the Broadband Networking Update Service page to update the firmware of your device. If the automatic update fails, go to the "Manual Update" section. Manual update 1. Download the MSBNDownload.exe firmware update. To do this, visit the following Microsoft Web site: http://go.microsoft.com/fwlink/?linkid=6... (http://go.microsoft.com/fwlink/?linkid=6790) 2. Save the file to a location such as your desktop or the My Documents folder. 3. If you are updating a wireless base station, use an Ethernet cable to connect your computer to your base station. 4. To run the update, double-click the MSBNDownload file. 5. Follow the instructions that appear on the screen to update the firmware of your device. While the firmware is being saved to your base station, the power light on the base station blinks and then turns orange. When the light is solid green, the update is completed. If the update fails, the power light continues to blink slowly until you successfully update the firmware. In this situation, you can try to update the firmware again, or you can reset the base station.

CAUSE This issue may occur if you change the file name from the default file name "Networksettings.xml". RESOLUTION To resolve this issue, do not click My settings are on a floppy on the Where are your network settings located? page in the Microsoft Broadband Networking Setup Wizard. Instead, click My settings are in a file available from this computer, locate the floppy disk drive, and then click your configuration file.

CAUSE This issue occurs if there is a problem with the domain name system (DNS) server settings on your network. RESOLUTION To resolve this issue, use the following procedures in the order presented. Determine if your DNS settings are the cause of the symptoms you are experiencing. To do this, following these steps: 1. Gather the Internet protocol (IP) settings from your computer. a. Click Start, click Run, type CMD, and then press ENTER. b. At the Command prompt, type ipconfig, and then press ENTER. c. Make a note of the information that is returned. You can copy and paste the output in another program, and then print it if you want. 2. Use the Ping.exe file to check your hardware. For additional information about how to use Ping.exe, click the following article number to view the article in the Microsoft Knowledge Base: 814155 (http://support.microsoft.com/kb/814155/EN-US/) MSBBN: How to Use Ping.exe to Check Your Microsoft Broadband Network Adapter 3. Bypass your Base Station, and connect your computer directly to your broadband modem. ? If you can access Internet Web sites as expected, the problem is most likely in the settings on your Base Station or on your computer. ? If you still cannot access the Internet, there may be a problem with your modem settings. Contact your ISP, or see the documentation that came with your broadband modem. If your network is functioning correctly internally, and you still cannot access Internet Web sites, there may be a problem with your DNS settings. To configure your DNS settings, you must know what the correct DNS settings are for your Internet Service Provider (ISP). See your ISP or the documentation that they provided when you signed up for service with them. To resolve this issue, following these steps: 1. Open the Microsoft Broadband Networking Utility (BNU), click Base Station Management Tool on the Tools menu, and then log into the Base Station Management Tool. 2. In the Base Station Management Tool, click Wide Area Network in the navigation list. 3. Select the appropriate type of Internet connection under Internet Connection Type, and then type the appropriate information.

Back up base station settings Before you start, back up the current settings for your base station. To do this, follow these steps: 1. Start the Microsoft Broadband Network Utility. 2. On the Tools menu, click Management Tool. 3. When you are prompted to, log on to the base station. To do this, use the password that you created when you ran the Setup Wizard the first time. If you did not run the Setup Wizard, use the following default base station password: admin 4. On the Management menu, click Back up and Restore Settings. 5. Click Back Up Settings. 6. Click Save. 7. Type a name for the file that contains your base station settings or use the default name Config.bin. 8. Click the folder where you want to save the file, and then click Save. Back to the top Back to the top Disable firewall or antivirus programs For information about how to disable your firewall or antivirus programs, view the documentation that came with the program, or contact the manufacturer's technical support. Back to the top Back to the top Install firmware update Warning Do not install the firmware update from a computer that is connected to your base station by using a wireless network connection. If your wireless signal is interrupted, weakened, or interfered with while the firmware update is running, your base station may become unusable. Automatic update 1. Start the Microsoft Broadband Network Utility. 2. On the Help menu, click Check for Updates Online. The Broadband Networking Update Service checks for updates by connecting to Microsoft. This can take several minutes, depending on your connection speed. If any new updates are available, a download screen appears. Otherwise, you receive a ?No new updates are available? message. 3. Follow the instructions on the Broadband Networking Update Service page to update the firmware of your device. If the automatic update fails, go to the "Manual Update" section. Manual update 1. Download the MSBNDownload.exe firmware update. To do this, visit the following Microsoft Web site: http://go.microsoft.com/fwlink/?linkid=6790 (http://go.microsoft.com/fwlink/?linkid=6790) 2. Save the file to a location such as your desktop or the My Documents folder. 3. If you are updating a wireless base station, use an Ethernet cable to connect your computer to your base station. 4. To run the update, double-click the MSBNDownload file. 5. Follow the instructions that appear on the screen to update the firmware of your device. While the firmware is being saved to your base station, the power light on the base station blinks and then turns orange. When the light is solid green, the update is completed. If the update fails, the power light continues to blink slowly until you successfully update the firmware. In this situation, you can try to update the firmware again, or you can reset the base station.

CAUSE This issue may occur if you change the file name from the default file name "Networksettings.xml". RESOLUTION To resolve this issue, do not click My settings are on a floppy on the Where are your network settings located? page in the Microsoft Broadband Networking Setup Wizard. Instead, click My settings are in a file available from this computer, locate the floppy disk drive, and then click your configuration file.