WEP Encryption How do I enable WEP Encryption on my DI-514, DI-524, DI-614+, DI-624, DI-624S, DI-774, or DI-784 wireless router?

Hi,
Go to your router setup and set you enable your WEP setting.

Thanks for using FixYa.

It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption.

Note: Your network will slow down and wireless signal may degrade when enabling encryption due to the added overhead.

Step 1 Log into the web configuration of the router by opening up a web browser and typing in the IP address of the router (192.168.0.1).

Click here if you cannot access the web-based configuration.

Step 2 Enter your username (admin) and your password (blank by default). Click OK . Click the Home tab and click the Wireless button on the left hand side of the screen.



Step 3 Select Enable next to the WEP radio buttons. For WEP encryption select 64, 128, or 256-bit encryption. For the Key type select HEX. If you have an option for Authentication type, select Shared Key.

Step 4 Select Key 1. Enter a Hex encryption key that you make up. The length of the encryption key will depend on what you selected under WEP Encryption.

64-bit encryption 10 characters

128-bit encryption 26 characters

256-bit encryption 58 characters (available on DI-614+ only)

The encryption key is HEX, meaning 0-9 and A-F are valid characters. For example, A4583DFF1A (64-bit HEX key).

Step 5 Click on the Apply button then click on the Continue button to save your settings.

Step 1 Log into the web configuration of the router by opening up a web browser and typing in the IP address of the router (192.168.0.1).

Click here if you cannot access the web-based configuration.

Step 2 Enter your username (admin) and your password (blank by default). Click OK . Click the Home tab and click the Wireless button on the left hand side of the screen.



Step 3 Select Enable next to the WEP radio buttons. For WEP encryption select 64, 128, or 256-bit encryption. For the Key type select HEX. If you have an option for Authentication type, select Shared Key.

Step 4 Select Key 1. Enter a Hex encryption key that you make up. The length of the encryption key will depend on what you selected under WEP Encryption.

64-bit encryption 10 characters

128-bit encryption 26 characters

256-bit encryption 58 characters (available on DI-614+ only)

The encryption key is HEX, meaning 0-9 and A-F are valid characters. For example, A4583DFF1A (64-bit HEX key).

Step 5 Click on the Apply button then click on the Continue button to save your settings.

Note: If using non-D-Link adapters, please refer to the manufacturer´s documentation on enabling encryption.

How do I enable encryption on my D-Link adapters?

If you need more help come back.Post /thumbs / testimonial are welcome!

It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption.

Note: Your network will slow down and wireless signal may degrade when enabling encryption due to the added overhead.

Step 1 Log into the web configuration of the router by opening up a web browser and typing in the IP address of the router (192.168.0.1).

Click here if you cannot access the web-based configuration.

Step 2 Enter your username (admin) and your password (blank by default). Click OK . Click the Home tab and click the Wireless button on the left hand side of the screen.



Step 3 Select Enable next to the WEP radio buttons. For WEP encryption select 64, 128, or 256-bit encryption. For the Key type select HEX. If you have an option for Authentication type, select Shared Key.

Step 4 Select Key 1. Enter a Hex encryption key that you make up. The length of the encryption key will depend on what you selected under WEP Encryption.

64-bit encryption 10 characters

128-bit encryption 26 characters

256-bit encryption 58 characters (available on DI-614+ only)

The encryption key is HEX, meaning 0-9 and A-F are valid characters. For example, A4583DFF1A (64-bit HEX key).

Step 5 Click on the Apply button then click on the Continue button to save your settings.

Enable WAP/WEP encryption, in the routers setup. Check your manual or DL the one below. ftp://ftp.dlink.co.uk/di_broadband_gateways/di-524/di-524_manual.pdf

When you have the wireless signal with a lock it indicates that your wireless network is secured.
Your wireless network has a security key enabled
Access the router page
Go to the wireless settings or WAN settings
Check what is the security mode(WEP/WPA)
If WEP check which Key is selected(key1or2or3or4)
If you are not able to find the key create a new one
If you change the key here ensure that it is updated on the wireless computers as well

I had this problem, My wirless router is using WEP Authentication with a "Shared Key". I had to change this to either Open or Automatic on the router.

u have to setup as wep
then enable secure network then set encryption key.wihc is prompt for connect network.

I would try using the hex value generated from your password by your WEP enabled router instead of the password itself. Windows has always been a little funny with WEP and I've always had better luck using the hex value my router generates.

It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Note: Your network will slow down and wireless signal may degrade when enabling encryption due to the added overhead. Step 1 Log into the web configuration of the router by opening up a web browser and typing in the IP address of the router (192.168.0.1). Step 2 Enter your username (admin) and your password (blank by default). Click OK . Click the Home tab and click the Wireless button on the left hand side of the screen. Step 3 Select Enable next to the WEP radio buttons. For WEP encryption select 64, 128, or 256-bit encryption. For the Key type select HEX. If you have an option for Authentication type, select Shared Key. Step 4 Select Key 1. Enter a Hex encryption key that you make up. The length of the encryption key will depend on what you selected under WEP Encryption. 64-bit encryption 10 characters 128-bit encryption 26 characters 256-bit encryption 58 characters (available on DI-614+ only) The encryption key is HEX, meaning 0-9 and A-F are valid characters. For example, A4583DFF1A (64-bit HEX key). Step 5 Click on the Apply button then click on the Continue button to save your settings. Note: If using non-D-Link adapters, please refer to the manufacturer´s documentation on enabling encryption.