Question about Belkin Wireless Cable/DSL Gateway Router

2 Answers

What are the wireless specifications of the 802.11b Wireless Router (F5D6231-4)?

Posted by Anonymous on

Ad

2 Answers

Anonymous

I don't have drivers to my router I lost it, please help me for put operative my router
Thank's

Posted on Jun 07, 2008

Ad

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 128 Answers

F5D6231-4 802.11b Wireless Cable/DSL Gateway Router Output Power +13dBm-20dBm (50mW) (max.) Range (ft/Meters) 11 Mbps 5.5 Mbps 2 Mbps 1 Mbps Outdoors 590 ft (180m) 980 ft (300m) 1475 ft (450m) 1800 ft (550m) Indoors 50 ft (15m) 125 ft (38m) 150 ft (46m) 300 ft (90m) Reciever Sensitivity -76 dBm -80 dBm -80 dBm -80 dBm

Posted on Feb 16, 2006

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Can't get conection from router to lap top . just had lt cleaned out. it was hooked up before.

1. Each wireless device has to be allow to connect to the router via a specific IP address assigned by the router in its router table.
It also can setup a wireless device, such as a laptop or phone via a MAC Address ( Media Access Control) number that is assigned to almost every wireless device.
2. Check your user manual for correct firewall and wireless setup.
3. Your manual should be on the CD that came with your router (PDF format)
0helpful
1answer

How do I block site in a N1 Wireless Router?

You're no able to block specific sites in this modem. You'll need parental control software for this.
0helpful
1answer

I have two laptops and want to set up a wireless network. I have the wireless set up but it isn't secure. When I go in to the Homegroups page it asks me for a 4 or 8 digit PIN number found on the router....

If you don't know it, you won't be able to automate your Wifi Protected Setup (WPS). The pin is a very specific way to prevent yourself from always having to remember codes, keys, passphrases, etc. Without it, its like saying that you want to to connect to Bank of America, and that it's just okay because you want it to happen.

The following is taken from the ESR-9753 manual:



- Wi-Fi Protected Setup (WPS)

WPS is the simplest way to establish a connection between the wireless clients
and the wireless router. You don’t have to select the encryption mode and fill in a
long encryption passphrase every time when you try to setup a wireless
connection. You only need to press a button on both wireless client and wireless
router, and the WPS will do the rest for you.

The wireless router supports two types of WPS: WPS via Push Button and
WPS via PIN code. If you want to use the Push Button, you have to push a
specific button on the wireless client or in the utility of the wireless client to start
the WPS mode, and switch the wireless router to WPS mode. You can simply
push the WPS button of the wireless router, or click the ‘Start to Process’ button
in the web configuration interface. If you want to use the PIN code, you have to
know the PIN code of the wireless client and switch it to WPS mode, then fill-in
the PIN code of the wireless client through the web configuration interface of the
wireless router.
0helpful
1answer

How does one go about setting up his own wifi system in my apt

Get an access point or wireless router.
Connect the AP or wireless router to your network.
Configure the AP/router to use encryption
Get a client adapter for your client device, and configure it to connect to your network.

That's it in a nutshell.

If you have more specific questions, I can give you more specific answers.
0helpful
2answers

How can i turn the wireless on? the led for wireless is off?i cant find any switch except for the reset.

The wireless part of a router (AP = Access Point) is normally "switched" on or off by way of a setting in the routers configuration - check your owners manual on how to do this. There is no physical switch as such.

Also, the wireless light only lights when a wireless device has established a wireless connection to the AP. Even though the AP maybe enabled and working, until a wireless device connects, the light remains unlit.

I dont know this exact model of router so cant give specifics on how to set it up, but hopefully if you can find your manual, this gives you a starting point.
2helpful
2answers

Cannot get drivers to install

Hi there,
You will find you LAN (BroadcomLAN driver 4.28) or (Broadcom Giga LAN driver 8.27.1) storage (Intel chip set driver) and Wireless (Broadcomm 802.11b+g wireless) or (Intel 802,11b+g Wireless LAN driver 9.0.1.9)  ->drivers from here:

Plz let me know how you go
5cb61ca.png

regards /Teis
0helpful
1answer

MN520 adaptor will not see my new Netgear WGR614 wireless router

The only protocol your older wireless adapter will connect to is 802.11b. I would say you will need to get another wireless adapter for the older computer. I would look at your router specification to see if it supports 802.11b, I am thinking it probably doesn't and that is why it cannot see the network. I will send a link to your cards specifications.

I’m happy to help further over the phone at https://www.6ya.com/expert/adrienne_b03fb46fc6334991

0helpful
1answer

Wireless router

The problem is the Linksys wireless router is not properly configured. Try downloading the automatic configuration file which can be accessed from the Linksys site for your specific model wireless router.

Hope this helps you.
0helpful
1answer

Helo top experts

i assume that your computer can access the internet while hardwired to the wireless-g router. if so, you just need to connect your wireless computer to the wireless signal of the wireless-g router. you just need to scan or view the available networks detected by your wireless computer and select the wireless name (ssid) of your wireless-g router. make sure to enter the correct wireless security (network key) if it's enabled on your router. i hope this'll help you but if you can't still access the internet wirelessly, provide the specific model number of your wireless-g router, specify if you're using a laptop or a wireless desktop, and the brand and model of your wireless card/adapter
0helpful
1answer

Laptop with 2 wire will not connect to wireless router

You need to be a little more specific on this issue if you wish to get assistance.

Best,
Bob
Not finding what you are looking for?
Belkin Wireless Cable/DSL Gateway Router Logo

Related Topics:

172 views

Ask a Question

Usually answered in minutes!

Top Belkin Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2278 Answers

Resolution IT Dubai
Resolution IT Dubai

Level 3 Expert

541 Answers

Ekse

Level 3 Expert

13435 Answers

Are you a Belkin Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...