I need an instruction manual for a DMC image transfer machine model GT-201A.

Buy new imaging unit, part #4163-612
then follow instructions here: http://www.manualslib.com/manual/611548/Konica-Minolta-Di-200.html?page=56#manual

Photo transfer from the camera to a computer is usually done with a USB cable. For detailed instructions on how to transfer the pictures, check out the user manual:
Panasonic DMC FX8 manual

Operating Instructions. Digital Camera. Model No. DMC-FZ8, check this link panasonic.com/OPERMANPDF/DMCFZ8.PDF or click over next image...



Good luck (remember to rate this answer).

You can view this manual free online by clicking the >> and http://www.sewingonline.co.uk/instructions/singer6235/
Hope this helps!

You do with Samsung pc studio

OR

click on Menu > Settings > Phone Settings > Pc Connections > Mass Storage

NOW YOU WILL BE ABLE TO BROWSE THE FOLDERS AND FIND WHERE THE PICTURES ARE STORED.

YOU NEED A DATACABLE or BLUETOOTH DONGLE

The manual recommends 4 Amp Slow blow for 115 volt operation or 2 Amp Slow blow for 230 Volt operation for the 201a.
http://s3.amazonaws.com/samsontech/related_docs/Servo201a_OM_5L_v1_1.pdf

For the 260 Amp manual shows 10 Amp normal for 115 volt operation and 5 Amp nomal for 230 volt operation.
http://s3.amazonaws.com/samsontech/related_docs/ACF1AAF.pdf

When this machine was started after connecting the Color Image Reader-E1/F1, the screen for the shutdown sequence appeared (and E732-9999 was recorded as an error history in service mode). When the main power switch was turned OFF/ON by following the instruction on the screen, the error code "E732-8888" was displayed. When connecting the Color Image Reader-E1/F1, follow the field remedy below.
- E732-9999 is recorded when a printer model detects a scanner for the first time. (This is not an error code but an alert.)
- E732-8888 can be displayed when a different scanner is connected to this machine.
1. Connect the Color Image Reader to this machine. (Do not connect the DDI cable).
2. Turn ON the main power switch.
3. Change the setting values of the following service mode items.
- Service mode > COPIER > Option > BODY > W/SCNR: from '0' to '1'.
- Service mode > COPIER > Option > BODY > SCANTYPE: from '1' to '0'.
Reference: For the Color Image Reader-E1/F1, this mode has to be set to '0'. On the other hand, it has to be set to '1' for the Duplex Color Image Reader-G1.
- Color Image Reader-E1: Platen cover model
- Duplex Color Image Reader-F1: Two-sided reversal reading type ADF model (DADF-M1)
- Duplex Color Image Reader-G1: Two-sided simultaneous reading type ADF model (DADF-T1: only for the iRC5180)
4. Turn OFF the main power switch, and connect the DDI cable.
5. Turn the main power switch ON.
Note: How to turn OFF the main power switch.
When turning off the main power switch, be sure to follow the steps below to protect the HDD inside this machine.
1. Hold down the control panel switch for 3 sec or more.
2. Following the instruction displayed on the shutdown screen, operate the control panel. (The main power switch is turned OFF automatically.)
3. If there is a need to unplug the power cord (from the wall outlet), perform step1 and 2 above before unplugging it.

.here is the solution when you have the photos to transfer form you digicam,
you have to insert the usb cable to the pc,
you will get a pop like->open with (use open file/folder)
after you select there will a folder.
so for finding the right folder.you have to click menu->thumbnails
then start searching the image folder and locate it,
if you find the folder click
mycomputer->tools->folder option->view->showo all hidden files.

check the image folder you respected image file will be there...
is not jus add a comment ill post another solution.

Operating instructions manual is available free at:
http://www2.panasonic.com/consumer-electronics/support/Cameras-Camcorders/Digital-Cameras/Lumix-Digital-Cameras/model.DMC-ZS3K

You can download required user manual from HERE or click Panasonic Support and type model number in box to get manual.