Can I use the PDC 700 camera with Windows XP?

Windows 7 has a builtin decoder program for all camera multimedia devices. Navigate through the list of available programs to ascertain the media program that is compartible to the camera. usually the camera should be connected to the computer for detection of any compartibility be achieved. Capture media with camera, connect the camera with USB cables to the computer. Also, cameras that have storage media would require to insert the media into computers that are media component compartibel to attain multimedia transfer.

According to the actual manuel and other info on this,  it will only hold as high as a 48x.

This message appears because Windows XP did not originally support the USB 2.0 specification. However, as of May 2002, the final release version of the Microsoft USB 2.0 drivers for Windows XP is available at the Windows Update Site. The driver is designated Microsoft USB Driver Version 5.1.2600.0.

This message appears because Windows XP did not originally support the USB 2.0 specification. However, as of May 2002, the final release version of the Microsoft USB 2.0 drivers for Windows XP is available at the Windows Update Site. The driver is designated Microsoft USB Driver Version 5.1.2600.0.

This message appears because Windows XP did not originally support the USB 2.0 specification. However, as of May 2002, the final release version of the Microsoft USB 2.0 drivers for Windows XP is available at the Windows Update Site. The driver is designated Microsoft USB Driver Version 5.1.2600.0.

The "Connection failed" error message indicates a communications problem in the USB connection between the camera and the computer. Simply put, the computer cannot find the camera it is being asked to connect with. There is usually no single "most likely" reason for the conflict -- it could be a hardware issue as easily as it could be a software issue. Fortunately, the most common causes of this error message are also the most easily identified: * Make sure that the computer's operating system is USB compatible. Microsoft Windows 95 and NT operating systems are not compatible with USB technology. (In addition, PhotoMAX and PhotoImpression software cannot be installed on Windows NT systems.) If you have an incompatible operating system, you must upgrade to Windows 98, Me or 2000 to use a USB connection. Your computer must also have the appropriate USB connectors. NOTE: This camera cannot make a USB connection with a computer running Windows XP. * Make sure that the camera power is on. Follow the camera instructions to turn the camera on. Some cameras conserve battery power by turning off automatically after a few minutes of inactivity. If necessary, install new batteries or connect the camera to AC power (if it has an AC power adapter). * Make sure that the camera is correctly set to access images. Make sure the camera is turned on and that its mode dial (if it has one) is correctly set for transferring pictures to the computer. Refer to the camera user guide for more information. * Make sure that the camera cable has not been damaged or become disconnected from the computer. Confirm that both of the connectors are firmly attached. Check the cable for breaks, kinks or other defects, and check the connectors for bent or broken pins. If the cable is broken or kinked, obtain a new cable.

Yes, you can use the camera with Windows XP, but you will not be able to use the serial port to download your photos. Only USB port downloads are supported under Windows XP for the PDC 640CF camera.

The PDC 700 camera TWAIN driver is not 100% compatible with Windows Me because it does not support USB downloads. No new driver software is available from Polaroid -- however, a compatible TWAIN driver is available from a third-party source. The Pretec DC-800 is the functional equivalent of Polaroid's PDC 700. Pretec's DC-800 Setup Disk for Windows 95/98/ME/2000 is available for download at its online Driver Download Center. Testing done by Polaroid has shown that this driver works with the PDC 700 using the listed operating systems, including Windows Me. When accessing the camera with image editing software compatible with the computer's operating system, the camera driver appears as Digital Camera 1024X768 Driver.

Yes -- with some minor modifications, you should be able to use your PDC 1300 with a computer running Windows XP.

Yes -- with some minor modifications, you should be able use your PDC 640 camera with a computer running Windows XP.