20 Most Recent Westinghouse WST2000 IntelliBLEND Work Top Blender Questions & Answers


First, If it is plastic, heat it with hot water. If It is metal same:)

Westinghouse... | Answered on Oct 27, 2009


either the motor is inoperable, or is improperly wired. return it to the retailer. that is assuming you have the cup firmly seated before you try to operate the machine.also if the control panel has more than one speed make certain that only one button, or switch position is engaged

Westinghouse... | Answered on Nov 12, 2008


Do you hear it hum when you try to turn it on?
If yes, remove the cup. Try again... if the motor runs, try moving the blade by hand. If it is seized, remove it and clean it to free it again.
If not, possibly blown windings on the motor or divider circuit (which supplies different voltages to the motor for the different blend speeds). Repair will be required in either case.

Westinghouse... | Answered on Oct 25, 2008


I have had my blender sitting for over a year ( only used it once ) because of the same problem and asked my husband to take a look at it... he opened it ... cut the zip ties took the metal banding off ( note only one side of the motor has the metal banding). What you need to get at is behind the first (I think) resistor. Behind that is a thermal fuse (found at radio shack part # 270-1320 about $1.96). you will need some kind of tester to check the ohms going through it (should read zero) the bad one on mine read 334 ohms and you will need a soldering iron to put it back together. Actually a good project for someone who loves to tinker with this.

Westinghouse... | Answered on Jun 29, 2008


The lighter flickering on your blender is letting you know that it is not working.Make sure that the blender isn't jamming
Another possible cause of the blender not working maybe because of it jamming. For that you must first have to disassemble the drive and then turn the blade shaft. If it seems to be jammed, check what is the causing it to become jammed . In most cases it is debris that are stuck in the blades of the blender that causes the jamming.Or it could be the fuse went bad and needs to be replaced.

Blenders | Answered on Dec 21, 2020


This problem can come from both the blender and or even the circuit powering it. First make sure that the outlet you have your blender plugged into is powered and not ripped If your blender still is not turning on then you may have a faulty motor or motor connection. Or the fuse could be blown and needs to be replaced.Or it could also be jamming for this you must first need to disassemble the drive and then turn the blade shaft. If it seems to be stuck or jammed here check what is the causing it to be jamming. In most of the cases it is debris that are stuck in the blades of the blender that causes it to be stuck.

Blenders | Answered on Nov 30, 2020


https://www.amazon.co.uk/Gordon-Ramsay-Cooks-600w-Blender/dp/B003UTUO2M

Blenders | Answered on Nov 20, 2020


The blades may not be turning because the blade assembly is not fully tightened onto the blender bottle. Another reason could be that you are not putting the blender bottle and blade assembly into the blender base in the proper way. For more answers visit the Oster Blend-N-Go My Blend troubleshooting page: Oster Blend-N-Go My Blend Troubleshooting

Blenders | Answered on Nov 20, 2020

Not finding what you are looking for?
Westinghouse WST2000 IntelliBLEND Work Top Blender Logo

Popular Tags

12 questions posted

Ask a Question

Usually answered in minutes!

Top Westinghouse Blenders Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

ray gallant

Level 3 Expert

71004 Answers

Tom Chichester

Level 3 Expert

61131 Answers

Are you a Westinghouse Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Westinghouse Blenders

  • Westinghouse Blenders

Most Popular Question

intelli blender will not work

  • Blenders
Loading...